Open Access
Subscription or Fee Access
A Review on Metal Inert Gas Welding of Dissimilar Steels
Abstract
Joining of dissimilar metals has found its use extensively in power generation, electronic, nuclear reactors, petrochemical and chemical industries due to environmental concerns, energy saving, high performance, cost saving and so on. However efficient welding of dissimilar metals has posed a major challenge due to difference in thermal, mechanical and chemical properties of the materials to be joined under a common welding condition. This causes a steep gradient of the mechanical properties along the weld. A variety of problems come up in dissimilar welding like cracking, large weld residual stresses, migration of atoms during welding causing stress concentration on one side of the weld, compressive and tensile stresses, stress corrosion cracking, etc. In the present work dissimilar joints of steel and its alloys joined using MIG welding are studied, in order to identify the gaps in works carried out by the earlier researcher’s.
Keywords
References
E. Mahdi, E. O. Eltai, A. Rauf , The Impact of Metal Inert Gas Welding on the Corrosion and Mechanical behaviour of AA 6061 T6, Int. J. Electrochem. Sci., 9, 2014, pp.1087 – 1101.
Nur Azhani Abd Razak, Wai Loon Ng. Juliawati, Effects of MIG Welding To Corrosion Behaviour of Carbon Steel, Applied Mechanics and Materials, 2013, pp. 914-918.
Nur Azhani Abd Razak and Shing Shian Ng, Investigation Of Effects Of MIG Welding On Corrosion Behaviour Of AISI 1010 Carbon Steel, Journal of Mechanical Engineering and Sciences , 7,2014, pp. 1168-1178.
Nabendu Ghosh, Pradip Kumar Pal, Goutam Nandi, Parametric Optimization of MIG welding on 316L Austenitic Stainless Steel by Grey-Based Taguchi Method, Proceedings of Global Colloquium in Recent Advancement and Effectual Researches in Engineering, Science and Technology (RAEREST 2016), Procedia Technology ,25, 2016,pp.1038-1048.
Nabendu Ghosh, Pradip Kumar Pal, Goutam Nandi,GMAW dissimilar welding of AISI 409 ferritic stainless steel to AISI 316L austenitic stainless steel by using AISI 308 filler wire, Engineering Science and Technology, 20, 2017,pp.1334-1341.
Pappu Kumar, Prof. Prakash Kumar, Optimization of welding parameter (MIG Welding) using Taguchi Method, International Journal of Scientific Research and Education,4(11),2016,pp.2321-7545.
Kamaleshwar Dhar Dwivedi, Anurag Srivastava, Parametric Optimization of MIG Welding for Dissimilar Metals Using Taguchi Design Method, International Journal of Scientific Research in Science and Technology, 3(4),2017,pp.213-219.
A. Suresh Kumar, S. Sivaprakasam, V. Mugesh,H. Abdul Rahman,B. Ashok, K. Vijayakumar, Optimization of dissimilar materials on stainless steel (316L) and mild steel (IS 2062) in MIG welding process, International Journal of Recent Trends in Engineering & Research,4(4), 2018,pp.94-101.
Vikas Chauhan and Dr. R. S. Jadoun , Parametric optimization of MIG welding for stainless steel (SS-304) and low carbon steel using Taguchi Design Method, International Journal of Recent Scientific Research , 6(2),2015,pp.2662-2666.
Sudhir Kumar and Rajender Singh , Parametric Optimization of MIG Welding and SMAW Techniques on Different AISI Steels and Alloys, International Journal for Research in Engineering Application & Management, 4(8),2018,pp.465-470.
A.Narayana and T.Srihari, Optimization of weld bead geometry in MIG welding process using Response Surface Methodology, International Journal of Science & Technology, 2(4),2012,pp.27-34.
Bhuvan Bhardwaj, Ravinder Singh, To study the effects of welding parameters on MIG welding of stainless steel Alloy-202, International Journal of Science Technology & Engineering ,4(1), 2017,pp.131-141.
Naval Mahore Trapti Sharma, Study of MIG welding process with different type technique: A Review, International Journal of Science Technology & Engineering, 4(6), 2017, pp.1-5.
Prasenjit Mondal1, Dipankar Bose, Optimization of the process parameters for MIG welding of AISI 304 and IS 1079 using fuzzy logic method, International Research Journal of Engineering and Technology , 2(8), 2015,pp.443-448.
Aniket Narwadkar & Santosh Bhosle, Optimization of MIG Welding Parameters to Control the Angular Distortion in Fe410WA Steel, Materials and Manufacturing Processes,2015,pp-1-27.
Milind M. Ghogal, S. A. Patil Optimisation of process parameters of MIG Welding to improve Quality of weld by using Taguchi Methodology, International Journal of Engineering Research & Technology , 2(12), 2013, pp.3677- 3685.
A. Suresh Kumar, S. Sivaprakasam, V. Mugesh, H. Abdul Rahman, B. Ashok, K. Vijayaku , Optimization of dissimilar materials on stainless steel (316L) and mild steel (IS2062) in MIG welding process, International Journal of Recent Trends in Engineering & Research, 4(4), 2018 ,pp.94-101.
D.Bahar, Md. Nawaz Sharif, K. Shravan Kumar and D. Reddy ,Optimisation of MIG welding process for hardness and strength of welding joint using grey relational analysis. International Journal of Research in Advent Technology, 6(5),2018, pp.893-899.
Pawan Kumar, Dr.B.K.Roy, Nishant, Parameters Optimization for Gas Metal Arc Welding of Austenitic Stainless Steel (AISI 304) & Low Carbon Steel using Taguchi’s Technique , International Journal of Engineering and Management Research, 3(4), 2013, pp.18-22.
N. Ghosh , P.K. Pal, G. Nandi, Parametric optimization of MIG welding on 316L austenitic stainless steel by Taguchi method, International Scientific Journal published monthly by the World Academy of Materials and Manufacturing Engineering ,79(1), 2016, pp.27-36.
K.Sivasakthivel, K.Janarthanan, R.Rajkumar, Optimization of Welding Parameter in MIG Welding by Taguchi Method, International Journal of Advanced Research in Mechanical Engineering & Technology , 1(1),,2015,pp.36-39.
Shanti Lal Meena, Ravi Butola, Qasim Murtaza, Hardik Jayantilal, M.S.Niranjan, Metallurgical Investigations of Microstructure and Micro hardness across the various zones in Synergic MIG Welding of Stainless steel, Materials Today:Proceedings, 4,2017,pp.8240–8249.
Brijesh Kumar Maurya, Balwant Pratap, Avaneesh Kumar, Gopal Rana, Experimental analysis of dissimilar metal welds of mild steel and stainless steel International Research Journal of Engineering and Technology, 4(5),2017,pp.1744-1748.
Nabendu Ghosh, Pradip Kumar Pal and Goutam Nandi, Experimental Investigation on Dissimilar Welding By GMAW, Indian Journal of Science and Technology, 9(46), 2016,pp.1-3.
N .Ghosh, P.Kumar Pal and G.Nandi, Parametric optimization of dissimilar welding of AISI 409 ferritic stainless steel to AISI 316L Austenitic Stainless Steel by using PCA Method, Journal of Achievements In Material and Manufacturing Engineering, 75(1),2016, pp.24-33.
Ajit Hooda, Ashwani Dhingra and Satpal Sharma, Optimization of MIG welding process parameters to predict maximum yield strength in AISI 1040, International Journal of Mechanical Engineering and Robotics Research, 1(3), 2012,pp.203-213.
Makwana Vishal P, Rathod Raviraj M and Kavad Raju A, Analysis of process parameters for dissimilar metal using MIG Weldin, Project Report, 2016, Atmiya institute of technology and science, Rajkot.
Mayur D. Jagtap and Niyati Raut, A Review on Optimization of Welding Process using Different Statistical Techniques, International Journal for Research in Applied Science & Engineering Technology , 6(IV), 2018,pp.2097-2100.
R.Sudarshan and M.Devaiah, Effect of Process Parameters in MIG Welding on Mild Steel IS 2062, International Journal of Applied Engineering Research, 13(4), 2018,pp.2046-2054.
Jigar Shah, Gaurav Patel, Jatin Makwana, A Review on Optimization and Prediction of MIG Welding Process Parameters Using ANN, International Journal of Engineering Development and Research, 5(1),2017,pp.289-291.
K. Nageswara Rao, B.V.R.Ravi Kumar , M.T.Naik, Study and parameter optimization of dissimilar materials using MIG Welding Process, International Journal of Engineering and Techniques, 4(2), 2018,pp.1081-1085.
Rakesh Kumar Raushan and Dr. Prakash Kumar, Optimization of the process parameters for MIG welding of dissimilar welding using Taguchi method, International Journal for Research in Engineering Application & Management , 4(8), 2018,pp.164-169.
Ashishkumar Wahule and Prof. Kushal Wasankar, Multi-response Optimization of Process Parameters of TIG Welding for Dissimilar Metals (SS-304 and Fe-410) using Grey Relational Analysis, International Research Journal of Engineering and Technology, 5(6),2018,pp.986-993.
P.Kalaignar, S.Krishnamohan and R.Rengarajan, An investigation and welding characterization of dissimilar joints of alloy steel with SS410 through GMAW, International Journal of Emerging Technologies In Engineering Research , 5(6),2017,pp.35-40.
Aisha Al Ismail, Mutlag Shafi Fuhaid, Murali R V, An Experimental analysis on mechanical integrity of TIG-MIG hybrid weldments, International Journal of Mechanical and Production Engineering, 5(4),2017,pp.2320-2092.
Radha Raman Mishra, Visnu Kumar Tiwari and Rajesha S, A study of tensile strength of MIG and TIG welded dissimilar joints of mild steel and stainless steel, International Journal of Advances in Materials Science and Engineering 3(2),2014,pp.23-32.
Emmanuel O. Ogundimu, Esther T. Akinlabi And Mutiu F. Erinosho, study on microstructure and mechanical properties of 304 stainless steel joints by TIG–MIG hybrid welding, Surface Review and Letters, 25(1),2018,pp.1-14.
Md. Samir Khan, Vishwajeet Kumar, Prosun Mandal and Subhas Chandra Mondal, Experimental Investigation of Combined TIG-MIG Welding for 304 Stainless Steel Plates, International Conference on Mechanical, Materials and Renewable Energy, IOP Conf. Series: Materials Science and Engineering, 377,2018, 012067.
Saurabh Kumar Khotiyan, Comparison of Hardness and Tensile Strength of TIG and MIG Welding Using Stainless Steel-202, International Journal of Advance Engineering and Research Development, 4(12),2017,pp.264-267.
G.T. Gopalakrishna, B.S. Ajay Kumar, K.R. Vishnuc, S.D. Sundareshan and K.G. Satyanarayana, Analysis of Dissimilar Metal Welding of EN19 and SS304L, Int. J. Vehicle Structures & Systems, 10(4), 2018,246-250.
Md. Gaffar, Mudavath Shankar, Pampana Sampath Kumar, V.V.Satyanarayana, Experimental Investigation on Welded Joints of Dissimilar Steels, International Journal of Current Engineering and Technology, 7(3),2017,pp.800-807.
Subodh Kumar and A. R. Ansari, Experimental Investigation on Dissimilar Welding of Austenite and Ferrite Stainless Steel by MIG Welding Process, International journal of advance research of science and engineering,6(7), 2017,pp.1207-1218.
F. Varol, Investigation of Mechanical Properties of MIG-Brazed 304 Stainless Steel and EN 10292 Galvanized Steel Joints using Different Current Intensity, Special Issue of the 6th International Congress & Exhibition (APMAS2016), Acta Physica Polonica A,131(1), 2016,pp.34-35.
Van Nhat Nguyen ,Quoc Manh Nguyen and Shyh-Chour Huang, Microstructure and Mechanical Properties of Butt Joints between Stainless Steel SUS304L and Aluminum Alloy A6061-T6 by TIG Welding, Materials, 11(1136),2018,pp.1-13.
Shu Yufeng , Fan Sili and Xiong Changwei, Welding process of dissimilar metals controlled by PLC and it’s microstructure and properties, Results in Physics ,11, 2018,pp. 853–860.
B. Mvola, P. Kah, J. Martikainen and R. Suoranta, Dissimilar High-Strength Steels: Fusion Welded Joints, Mismatches and Challenges, Rev.Adv.Mater.Sci., 44, 2016, pp.146-159.
Sahil Nandwani, Mandeep Singh and Gaurav Sharma, Experimental Study on Weld Joint of SS-316 and MS-2062 their behavior & comparison on different process parameters with MIG Welding. International Journal of Research in Mechanical Engineering & Technology, 7(2), 2017,pp.165-169.
Abhishek Dayal, Pushpendra kumar and Shant kumar Jain, Welding of two dissimilar Steels with the help of MIG, International Journal of Engineering Science and Computing, 7(5), 2017,pp.11586-11592.
Belinga Mvola, Paul Kah and Jukka Martikainen, Welding of dissimilar non ferrous metals by GMAW Processes, International Journal of Mechanical and Materials Engineering , 9(21),2014,pp.1-11.
Muhamad Fadhli Bin Zainuddin, MIG welding of dissimilar metal using different thicknesses (Aluminium and Mild Steel), Project Report, 2012, University Malaysia, Pahang.
S. Maheshwaran and T.Senthilkumar , Experimental Investigation on Mechanical Property of MIG Welding Process, International Journal of Engineering Research & Technology , 5(13),2017,pp.1-4.
Hassan Kutty, Nishad Naduthodi, Shaimil Fithu, Vignesh, Analysis and Optimization of Parameters of Dissimilar Metal Welding, International Journal of Science Technology & Engineering, 4(9),2018,pp.10-15.
Belinga Mvola, Paul Kah, Jukka Martikainen, Raimo Suoranta, State-of-the art of advanced Gas Metal Arc Welding Processes: Dissimilar metal Welding, J Engineering Manufacture, 1(17), 2014,pp.1-17.
Eszter Kalacska, Kornel Majlinger, Eniko Reka Fabian and Russo Spena Pasquale, MIG welding of dissimilar advanced high strength steel sheets, Materials Science Forum, 885,2017, pp 80-85.
L. H. Shah And M. Ishak, Review of research process on Aluminium-Steel
Dissimilar Welding, Materials and Manufacturing Processes, 29, 2014,pp.928–933.
S.Senkathir, Arun Raj A.C, R.Manoj Samson and B.Aravind Kumar, Improvement of weldability of dissimilar metals using Inconal 718 and stainless steel in TIG Welding with different flux:SIO2,CR2O3 and TIO2, Journal of Advanced Research in Dynamical and Control Systems ,9(18), 2017,pp.1919-1926.
Refbacks
- There are currently no refbacks.