Open Access
Subscription or Fee Access
A Study on Factors Affecting the Tensile Welding Strength of Joint Using Taguchi Methods: A Review
Abstract
The welding process over the period of time has grown into a more formidable process. Its application has also increased manifolds. However, with the increase in applications, it is also important to know the about the factors which affects the most on the strength of the welds. In this paper, the tensile strength of the welded joint has been considered. The factors considered for the research are on the basis of the literature review which is the main part of
this paper. Moreover, for the research work, the Taguchi Design of experiments has been taken.
Keywords
References
G. Meneghetti, c. Guzzella and b. Atzori, Fatigue 2014, analysis of multipass welded joints considering residual stresses, International Journal of Fatigue 79 (2015) 75–85.
A. Seto, y. Yoshida and a. Galtier, 2004,Fatigue properties of arc-welded lap joints with weld startand end points,Fatigue FractEngng Mater Struct27, 1147–1155.
Andrea Carpinteri, Camilla Ronchei, Daniela Scorza, Sabrina Vantadori,2015, Fracture mechanics based approach to fatigue analysis of welded joints, Engineering Failure Analysis 49 (2015) 67–78.
VibhorPandhare, PravinRai, Bhupesh Kumar Lad, Santanu Das and KaziSabiruddin, 2016, Determination of factors affecting the bending strength of weld joint prepared by Gas Metal Arc Welding, International Journal of Advance Research in Engineering, Science & Technology(IJAREST), Vol. 2, No. 1, February 2016.
A l dhobale, prof h k mishra, 2015, review on effect of heat input on tensilestrength of butt weld joint using mig welding, International Journal of Advance Research in Engineering, Science &Technology(IJAREST), volume 2, issue 9, sep.-2015.
Brijesh Kumar Maurya, BalwantPratap, Avaneesh Kumar, GopalRana, 2017, Experimental analysis of dissimilar metal welds of mild steel and stainless steel,International Journal of Advance Research in Engineering, Science & Technology(IJAREST), Volume: 04 Issue: 05 May -2017
Subodh Kumar, A. R. Ansari, 2017,
Experimental Investigation on Dissimilar Welding of Austenite and Ferrite Stainless Steel by MIG Welding Process, International Journal of Advance Research in Engineering, Science & Technology(IJAREST),Vol No. 6, Issue No.7, July 2017
Patel Ujjvalkumar , Patel Uchit , 2015, Optimization Of Process Parameter in Arc Welding Process On DissimilarMaterial By Using ANOVA Method, International Journal of Advance Research in Engineering, Science & Technology(IJAREST), Volume 2,Issue 4, April- 2015.
K.Monika, M.BalaChennaiah , Dr.P.Nanda Kumar , Dr.K.Prahalada Rao,2013, International Journal of Advance Research in Engineering, Science & Technology(IJAREST), Vol. 2 Issue 9, September - 2013.
Abdul wahab H. Khuder,Esam J. Ebraheam, 2011, Study the Factors Effecting on Welding Joint of Dissimilar Metals, Al-Khwarizmi Engineering Journal, Vol. 7, No. 1, PP 76 - 81 (2011)
D.S. Nagesh, G.L. Datta, 2002, Prediction of weld bead geometry and penetration in shielded metal arc welding using artificial neural networks, Journal of Materials Processing Technology 123 (2002) 303–312.
RajkumarDuhan and Rajesh Nandal, “Maximizingtensile strength in AISI 50110 (En 31) welded joints usinggas metal arc (GMAW) welding”, International journal ofengineering sciences paradigms and researches, October(2013), Vol. 08, Issue 01, pp.- 41-57.
NiranjanPawaria, Suresh Kataria, AmitGoyal, Seeone Sharma, 2013, Effect of Heat Input and Shielding Gas on Hardness, Tensileand Impact Strength of 2.25 Cr-1Mo SteelWeld Metals in GMAW, IJRMET Vol. 3, Issue 2, May - Oct 2013