ASSESSMENT OF MECHANICAL PROPERTIES OF ALUMINIUM WITH FLY ASH REINFORCMENT

Authors

  • Akshoy Kumar Saha Student, Mechanical Engineering Department, Dr. B. C. Roy Engineering College, Durgapur,
  • Ayan Chatterjee Student, Mechanical Engineering Department, Dr. B. C. Roy Engineering College, Durgapur,
  • Trinanjan Bhadra Student, Mechanical Engineering Department, Dr. B. C. Roy Engineering College, Durgapur,
  • Chandan Chattoraj Professor, Mechanical Engineering Department, Dr. B. C. Roy Engineering College, Durgapur,

DOI:

https://doi.org/10.37591/joeam.v14i1.7033

Keywords:

Mechanical properties, Powder metallurgy, Aluminium compaction, Reinforced compaction

Abstract

There is always a demand for lighter but with high strength materials in many industrial
applications including automobile and aerospace industries. Reinforced aluminium
Aluminium has been used for these applications for many years. Researchers worked out with
a variety of reinforcements. In the present paper, use of fly ash is investigated by using
powder metallurgy technique. Fly ash composition can raise up to hardness, and density,
corrosion & wear rate can also be reduced. According to the findings of this study, fly ash
from industrial waste can be converted into industrial wealth through the creation of
lightweight composites with increased strength that can be utilized in the aviation and
automobile industries.

References

B.V. Subrahmanayam, S.V. Gopal Krishna, CH. Lakshmi Pornima, A. Srinivasa Rao,

International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 8,

Number 1 (2018), pp. 1-11

Parswajinan Chakravarti, Vijaya Ramnath, I. Anish Hilary, N. Chenbhaga Ram, A.

Mayandi, Investigation of Mechanical properties of Aluminium reinforced Fly ash with CNT.

Materials Science and Engineering 390 (2018) 012032 doi:10.1088/1757-

X/390/1/012032.

Govindarajan, Manikandan’s, Mohankumar.P, Raghul.R (2015) “Effect of E-waste

Aluminium with Fly ash composite for environment safety”, International Journal of

Scientific and Research Publications, Volume 5, Issue 10, October 2015 1 ISSN 2250-3153.

Shankar S. Hari Chandran s., Aluminium alloy reinforced with fly ash Techniques and

particle size, Issued on 13 April 2019 and accepted 28 May 2019, Journal Tribology 23,

pp.13 – 37.

Govindharajan.B, Manikandan.S, Mohankumar.P, Raghul.R(2015) “Effect of E-waste

Aluminium with Fly ash composite for environment safety”, International Journal of

Scientific and Research Publications, Volume 5, Issue 10, October 2015 1 ISSN 2250-3153.

Georgantzia, Evangelia & Gkantou, Michaela & Kamaris, George. (2020). Aluminium

alloys as structural material: A review of research. Engineering Structures. 227.

1016/j.engstruct.2020.111372.

Verma, Rajan & Sharma, Saurabh & Kumar, Dinesh. (2017). Analysis of Mechanical

Properties of Aluminium based Metal Matrix Composites Reinforced with Alumina and Sic.

International Journal of Engineering Research and. V6. 10.17577/IJERTV6IS030506.

Mohanakumara KC, RajaShekar H, Ghanaraja S and Ajitprasad SL (2014).

Development and mechanical properties of SiC reinforced cast and extrude Al based

metal matrix composite. International Conference on Advances in Manufacturing and

Materials Engineering, ICAMME 5 934-943.

Kuzumaki T et al., (1998). Materials Transactions 38 574–7.

Bijay Kumar Show, Dipak Kumar Mondal, Joydeep Maity,’’ Dry Sliding Wear

Behavior of Aluminum-Based Metal Matrix Composites with Single (Al2O3) and

Hybrid (Al2O3 + SiC)’’, Metallogr. Microstruct. Anal. 3 (2014) 11-29.

S.K. Chaudhury, C.S. Sivaramakrishnan and S.C. Panigrahi, “A new spray forming

technique for the preparation of aluminium rutile (TiO2), ex situ particle composite”, J.

Mater. Proces.Technol., 145 (2004) 385-390.

Barekar, N.; Tzamtzis, S., Dhindaw, B. K.; Patel, J.; Hari Babu, N. and Fan Z. (2009).

Processing of Aluminium-Graphite Particulate Metal Matrix Composites by Advanced

Shear Technology. “Journal of Materials Engineering and Performance” 1-11. DOI:

1007/s11665-009-9362-5.

Downloads

Published

2023-06-16

Issue

Vol. 14 No. 1 (2023)

Section

Review Article

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.