Design Process Parameter of Thread Manufacturing Process Optimized by Fuzzy Logic Methodology

Authors

  • M Singh Mechanical Engineering Department, Madhav Institute of Technology & Science, Gwalior, M.P., India
  • CS Malvi
  • P Gupta

DOI:

https://doi.org/10.3759/joise.v2i3.3508

Abstract

The threads are most widely used in many industries. For the industries which produce the thread, it is a key skill to adopt the accurate and precise machining of threads because there are so many parameters which affect the dimensions of thread. The aim of the study is to generate the threads with the considerations of the parameters (hardness, blank diameter and surface roughness) which are to be used. Due to this we can determine the dimensions of thread without doing the thread rolling process experiment; as a result if we know the value of the each parameter accurately than we can give the accurate dimensions of the threads before the rolling process and thus reduce the rejection of the threads in the thread forming industry.

References

Domblesky Joseph P, Feng Feng. A Parametric Study of Process Parameters in External Thread Rolling. J Mater Process Technol. 2002; 121(2–3): 341–349p.

Saglam H, Kus R. Performance of Internal Thread Rolling Head and the Mechanical Properties of Rolled Threads. International Advanced Technologies Symposium (IATS’11), Elazig, Turkey; 2011.

Gagg CR. Premature Failure of Thread Rolling Dies: Material Selection, Hardness Criteria and Case Studies. Eng Fail Anal. 2001; 8: 87–105p.

Bellman RE, Zadeh LA. Decision Making in a Fuzzy Environment. Manage Sci. 1970; 17: B.

Kamouneh Amir A, Jun Ni, David Stephenson, et al. Diagnosis of in Volutometric Issues in Flat Rolling of External Helical Gears through the Use of Finite Element Models. Int J Mach Tools Manufactur. 2007; 47: 1257–1262p.

Domblesky Joseph P, Feng Feng. A Parametric Study of Process Parameters in External Thread Rolling. J Mater Process Technol. 2002; 121: 341–349p.

Badami VG, Hege RE, Patterson SR. A Novel Method for Forming Fine Pitch Threads in Superinvar. Precis Eng. 2003; 27: 87–90p.

Zadeh LA. Fuzzy Sets. Information and Control. 1965; 8: 338–353p.

Kaufmann A, Gupta MM. Introduction to Fuzzy Arithmetic Theory & Application. New York: Van Nostrand Reinhold; 1991; 1: 5–18p.

Dickson Weber. Multi Objective Linear Model for Vendor Selection Criteria and Methods. Eur J Oper Res. 1991; 50: 2–18p.

Kandel A. Fuzzy expert systems. Boca Raton, FL: CRC Press; 1992.

Buffa, Jackson, Sharma. Multi Decision Making used Linear and Non-Linear Programming. Total Quality Environmental Management (TQEM). 1994; 3(4): 521–530p.

Mamdani, Sugeno, Li-xin International Journal of Industrial Engineering Technology. 1998; 3: 267–277p. ISSN 0974-3146

Amit Karani, Zhiling Guo. Apply Fuzzy Logic Approach to Intergraded Qualitative Survey Data into Traditional MCDM. Hawaii International Conference on System Sciences, IEEE. 2012; 7.

Downloads

Published

2019-11-18

Issue

Vol. 2 No. 3 (2015)

Section

Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.