Advanced Quantitative Analysis of Dynamic Recovery During Warm Working of FCC Alloys

Authors

  • Prantik Mukhopadhyay Defence Metallurgical Research Laboratory, Kanchanbagh, Hyderabad, India

DOI:

https://doi.org/10.37591/jomme.v12i1.6145

Keywords:

FCC Alloys, Bainitic Steel, Aluminium Alloys, SPD, Ausforming, Dislocation Dynamics and Recovery

Abstract

Metal working processes of warm working require an advanced quantitative analysis of dynamic and static recovery of dislocations to control microstructures and crucial shape forming properties. Feasibility of dynamic recovery by thermal glide and static recovery by climb of constricted jogs, applicable to ausforming, nano bulk forming by SPD and normalizing has been addressed to design new steels, used for hulls and tribologically superior bearings. Predictive dislocation recovery analysis shows Taylor factor as an important dynamic recovery controller for mean dislocation dynamics and crystallographic orientation dependent dislocation dynamics, to govern work hardening and recovery strain rate of materials. Taylor factor has been defined as glide plane specific stacking fault energy. In contrast to static recovery by climb, present mechanism has found that less stacking fault energy will have enhanced dynamic recovery kinetics. Predicted recovery kinetics has been qualitatively validated by frequency of low angle boundaries, formed during ausforming and normalizing, in regard to Taylor factors of crystallographic orientations of retained austenite, detected by EBSD. 

References

Humphreys FJ, Hatherly M (2004) Recrystallization and related annealing phenomena, Elsevier, Oxford.

Kubin L, Hoc T, Devincre B (2009) Dynamic recovery and its orientation dependence in face-centered cubic crystals, Acta Mater. 57: 2567-2575.

Bacroix B, Brenner R (2012) A phenomenological anisotropic description for dislocation storage and recovery processes in fcc crystals, Comp Mater. Sci. 54: 97-100.

Dieter G (1988) Mechanical metallurgy. SI Metric Ed. McGraw-Hill, London.

M. Crumbach M, G. Gottstein G (2004) Analysis of the activity of {110}〈110〉 slip in AA3103 by inverse modeling, Mater. Sci. Engg. A. 387-389: 282-287.

He J, Zhao A, Zhi C, Fan H (2015) Acceleration of nanobainite transformation by multi-step ausforming process, Scripta Mater. 107: 71–74.

Hirth JP, Lothe J (1982) Theory of dislocations 2nd Ed. John Wiley & Sons, New York.

Hull D, Bacon DJ (2011) Introduction to dislocations 5th Ed. Elsevier, London.

Radhakrishnan B, Sarma GB (2008) Coupled simulations of texture evolution during deformation and recrystallization of fcc and bcc metals, Mater. Sci. Engg. A. 494: 73-79.

Umezawa A, Inagaki H (2006), Development of cube recrystallization textures in high-purity Al, Z. Metllkd. 97: 49-58.

Baudin T, Julliard F, Paillard P, Penelle R (2000) Simulation of primary recrystallization from tem orientation data, Scr. Mater. 43: 63-68.

Vitek V (1975) Stacking faults on {111} and {110} planes in aluminium, Scr. Metall. 9: 611-615.

Koch CC (2003) Ductility in nanostructured and ultra fine grained materials: recent evidence for optimism, J. Metastable Nanocryst. Mater. 18: 9-20.

Chung CS, Kim JK, Kim HK, Kim WJ (2002) Improvement of high-cycle fatigue life in a 6061 Al alloy produced by equal channel angular pressing, Mater. Sci. Engg. A 337: 39-44.

Tanimoto H, Sakai S, Mizubayashi H (1999), Mechanical property of high density nanocrystalline gold prepared by gas deposition method, Nanostruct. Mater. 12: 751-756.

Meyers MA, Mishra A, Benson DJ (2006) Mechanical properties of nanocrystalline materials, Prog. Mater. Sci. 51: 427-556.

Kumar KS, Swygenhoven HV, Suresh S (2003) Mechanical behavior of nanocrystalline metals and alloys, Acta Mater. 51: 5743-5774.

Swygenhoven HV, Caro A (1997) Plastic behavior of nanophase Ni: A molecular dynamics computer simulation, Appl. Phys. Lett. 71: 1652-1654.

Swygenhoven HV, Derlet PM (2001) Grain-boundary sliding in nanocrystalline fcc metals, Phys. Rev. B 64 224105: 1-9.

Asaro RJ, Krysl P, Kad B (2003) Deformation mechanism transitions in nanoscale fcc metals Phil. Mag. 83: 733-743.

Liao XZ, Srinivasan SG, Zhao YH, Baskes MI, Zhu YT, Zhou F, Lavernia EJ, Xu HF (2004) Formation mechanism of wide stacking faults in nanocrystalline Al, Appl. Phys. Lett. 84: 3564-3566.

Iwahashi Y, Wang JT, Horita Z, Nemoto M, Langdon TG (1996) Principle of equal-channel angular pressing for the processing of ultra-fine grained materials, Scr. Mater. 35: 143-146.

Valiev RZ, Alexandrov IV (1999) Nanostructured materials from severe plastic deformation, Nanostruct. Mater. 12: 35-40.

Downloads

Published

2022-03-15

Issue

Vol. 12 No. 1 (2022)

Section

Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.