Open Access Open Access  Restricted Access Subscription or Fee Access

Effect of Curing Time on Physico-mechanical Properties on Dental Composite

Mayuri Gupta, A. K. Tyagi, Manoj Raula

Abstract


This study aim to investigate the influence of curing time on physical and mechanical properties of a dental composite cured by using LED light with intensity of 1500 mW/cm2 in the range of 440-480 nm. We prepared the glass ionomer powder by fusion of various inorganic components at high temperature and studied the influence of silica/alumina ratio keeping other inorganic salts such as Calcium fluoride (CaF2), Sodium Fluoride (NaF), Calcium carbonate (CaCO3), Cryolite (Na3AlF6) and Phosphorous oxide (P2O5) constant. Ratio of silica/alumina vary from 1:1, 1.5:1, 2:1 and 2:3 and study the mechanical properties i.e. compressive and flexural strength and results shows that 1.5:1 silica/alumina ratio gives highest compressive strength 130 MPa and flexural strength as 27 MPa respectively. Developed glass ionomer powder characterized by FTIR before and after fusion along with XRD and SEM-EDX which reveal that all inorganic components are completely fused and that all particles have irregular shapes with less than 20 micron size. Resultant glass ionomer powder mix with commercial polymer in recommended ratio and cured by LED with three different curing time 10 sec, 20 sec, 30 sec. and studied the physical and mechanical properties i.e. thermal stability, compressive strength and flexural strength. Thermal analysis indicate that composite cured by 10 sec have lowest thermal stability due to some uncured resin which also directly effect on compressive and flexural strength of composite. On the other hand composite cured by 20 sec shows highest thermal stability, Flexural and compressive strength while composite cured by 30 sec have no significant changes on their physico-mechanical properties.


Full Text:

PDF

References


Meshref A.A., Mazen A.A., El-Giushi M.A. and Ali W.Y., Effect of Curing Process on Compressive Properties of Dental Composite Resin. International Journal of Engineering and Information Systems (IJEAIS), 2019, 3: 5, 44–56.

Mithra N H., Priyadarshini H., Shruthi B., Deepika K, An evaluation of compressive strength of newer nanocomposite: An in vitro study. Journal of Conservative Dentistry, 2011, 14:1, 36–39.

DOI:10.4103/0972-0707.80734

Santos S.G.D., Moyses M.R., Alcantara C.E.P., Ribeiro J.C.R., and Ribeiro J.G.R., Flexural strength of a composite resin light cured with different exposure modes and immersed in ethanol or distilled water media. J Conserv Dent., 2012, 15: 4, 333–336. DOI: 10.4103/0972- 0707.101891.

Ceballos L., Fuentes M.V., Tafalla H., Martinez A., Flores J., Rodriguez J., Curing Effectiveness of Resin Composites at Different Exposure Times using LED and Halogen Units. J Clin Exp

Dent., 2009, 1:1, 8-13.

Sakaguchi R.L., Powers J.M., Craig’s Restorative Dental Materials, Thirteen edition, Elsevier, 2012, 190.

Sajjad A., Bakar W.Z.W., Mohamad D., Kannan T.P., Characterization and enhancement of physico-mechanical properties of glass ionomer cement by incorporating a novel nano zirconia silica hydroxyapatite composite synthesized via sol-gel. AIMS Materials Scienc, 2019, 6:5, 730– 747. DOI: 10.3934/matersci.2019.5.730

Felemban N. H. and Ebrahim M. I., Effects of adding silica particles on certain properties of resin‑modified glass‑ionomer cement, European Journal of Dentistry, 2016, 10: 2, 225-229. DOI:

4103/1305-7456.178318.

Bakar W.Z.W., Novel Upgrading of Conventional Glass Ionomer Cement Using Nanohydroxyapatite, Silica and Zirconia, Online Journal of Dentistry & Oral Health, 2020, 3: 5,

DOI: 10.33552/OJDOH.2020.03.000573.

Sidhu S. K. and Nicholson J.W., A Review of Glass-Ionomer Cements for Clinical Dentistry, J.of Funct. Biomater. 2016, 7:3, DOI: 10.3390/jfb7030016.

Tsuzuki F.M., Pascotto R.C., Malacarne L.C., Benton A.C., Neto A.M., Hoshino L.V.D.C., Souza M., Nicholson J.W. and Baesso M. L., Studies of the early stages of the dynamic setting process

of chemically activated restorative glass-ionomer cements, Biomaterial Investigations in

Dentistry, 2021, 8:1, 39–47, DOI:10.1080/26415275.2021.1898964.

Barra E.D. and Hill, R.G., Influence of glass composition on the properties of glass polyalkenoate cements. Part IIII: Influence of fluorite content. Biomaterials 2000, 21:6, 563–569,

DOI:10.1016/S0142-9612(99)00215-X.

Griffin S.G., Hill R.G., Influence of glass composition on the properties of glass polyalkenoate cements. Part IV: Influence of fluorine content. Biomaterials, 2000, 21:7, 693–698. DOI:

1016/s0142-9612(99)00216-1. Effect of Curing Time on Physico-mechanical Properties on Dental Composite Gupta et al.

Zilberman U., Ion exchanges between glass-ionomer restorative material and primary teeth components-an in vivo study, Oral Biology and Dentistry, 2014, DOI: 10.7243/2053-5775-2-1

Nakamura K., Abe S., Minamikawa H. and Yawaka Y., Calcium Charge and Release of Conventional Glass-Ionomer Cement Containing Nanoporous Silica, Materials, 2018, 11:8,

DOI:10.3390/ma11081295.

Lohbauer U., Dental Glass Ionomer Cements as Permanent Filling Materials? —Properties, Limitations and Future Trends. Materials, 2010, 3:1, 76-96, DOI: 10.3390/ma3010076.

Thoo V.W.F., Zainuddin N., Matori K.A., and Abdullah S.A., Studies on the Potential of Waste Soda Lime Silica Glass in Glass Ionomer Cement Production, Advances in Materials Science and

Engineering, 2013, DOI:10.1155/2013/395012.

Sakaguchi R.L., Powers J.M., Craig’s, Restorative Dental Materials, Thirteen edition Elsevier, 2012, 33–143.

Saade E.G., Bandeca M.C., Rastelli A.N.S., Bagnato V.S., and Porto-Neto S. T., Influence of PreHeat Treatment and Different Light-Curing Units on Vickers Hardness of a Microhybrid

Composite Resin. Laser Physics, 2009, 19:6, 11276–1281, DOI: 10.1134/S1054660X09060164

Garcia A.H., Lozano M.A.M., Vila J.C., Escribano A.B., Galve P.F., Composite resins. A review of the Materials and Clinical Indications. Med Oral Patol Oral Cir Bucal, 2006, 11, 215–20.

Ilday N.O., Bayindir Y.Z., Bayindir F., Gurpinar A., The effect of light curing units, curing time, and veneering materials on resin cement microhardness. Journal of Dental Sciences, 2013, 8:2,

-146, DOI:10.1016/j.jds.2012.09.014.

Meganadhan A., Sanjeev K., Sekar M., Influence of Silica Fumes on Compressive Strength and Wear Properties of Glass Ionomer Cement in Dentistry, J Evolution Med Dent Sci, 2021, 10:20.

Al-Tae'e S. S., Almitwalli O. M., and Farid, S. B. H., Preparation of Glass Ionomer Cement from Recycled Low Alumina Glass, Karbala International Journal of Modern Science, 2020, 6:2,

DOI:10.33640/2405-609X.1410.

Shaibani D.A., Bakhadher W., Bajafar S., Bamusa B., Binjubair M., Baties M., Ramadan A. and Algamdi M., Conventional Glass-Ionomer Restorative Material; An Overview. International Journal of Current Research, 2019, 11:4, 2925–2929, DOI:10.24941/ijcr.35059.04.2019.

Gundogdu M., Kurklu D., Yanikoglu N. and Kul E., The Evaluation of Flexural Strength of Composite Resin Materials with and without Fiber. Dentistry, 2014, 4:9, DOI:10.4172/2157- 7633.1000259.

A. Stamboulis, R.V. Lawb, R.G. Hill, Characterisation of commercial ionomer glasses using magic angle nuclear magnetic resonance (MAS-NMR). Biomaterials, 2004, 25:17, 3907-3913,

DOI: 10.1016/j.biomaterials.2003.10.074.

Gupta M., Tyagi A.K. and Raula M., Synthesis of Bis-GMA Grafted Co-Polymer of Acrylic– Itaconic Acid and its Composite, Polymer Science, Series B, 2022.

DOI:10.1134/S1560090422700130.




DOI: https://doi.org/10.37591/jopc.v10i3.6607

Refbacks

  • There are currently no refbacks.