Open Access Open Access  Restricted Access Subscription or Fee Access

Exploring the Influence of SS 316L Nanoparticle Integration on the Flexural Strength of PMMA

Upender Punia, Ramesh Kumar Garg

Abstract


In the present study, a nano composite PMMA was prepared with the help of hot plate magnetic stirring and probe sonication at different loading conditions of nano sized reinforcement material SS 316L. In order to study the effect of independent factors (the amount of reinforcement material, stirring speed, and sonication time) on response variable (flexural strength), the central composite experimental design of response surface methodology (RSM) was utilized. The analysis of the RSM results indicated that the experimental data were most accurately represented by a quadratic polynomial model. The optimum preparation conditions for PMMA nano-composite to achieve the best specific wear rate and flexural strength were found to be as follows: the addition of 1.14% (w/w) of reinforcement material SS 316L, a stirring speed of 1307 rpm, and a sonication time of 24.26 minutes. At the optimized process parameters, the experimental values for compression strength were measured at 92.31MPa which were found to closely align with the predicted values confirming the reliability and accuracy of the developed RSM model. The results of this study hold great significance in the fabrication process of long-term provisional dental crowns and bridges.

Keywords


Composite materials, Reinforcement, Additive manufacturing, Mechanical properties, Response surface methodology

Full Text:

PDF

References


Abdel-Karim UM, Kenawy ERS. Synthesis of zirconia, organic and hybrid nanofibers for reinforcement of polymethyl methacrylate denture base: Evaluation of flexural strength and modulus, fracture toughness and impact strength. Tanta Dental Journal. 2019; 16(1), 12.

Abdulhamed AN, Mohammed AM. Evaluation of thermal conductivity of alumina reinforced heat cure acrylic resin and some other properties. J Bagh Coll Dent. 2010; 22(3), 1-6.

Chen Y, Caneli G, Almousa R, et al. A novel antibacterial zirconia-containing PMMA bone cement. J Mech Behav Biomed Mater. 2022; 129, 105135.

Li GH, Chen S, Grymak A, et al. Fibre-reinforced and repaired PMMA denture base resin: Effect of placement on the flexural strength and load-bearing capacity. . J Mech Behav Biomed Mater. 2021; 124, 104828.

Alqahtani M. Mechanical properties enhancement of self-cured PMMA reinforced with zirconia and boron nitride nanopowders for high-performance dental materials. . J Mech Behav Biomed Mater. 2020; 110, 103937.

Mousavi A, Aliha MRM, Imani DM. Effects of biocompatible Nanofillers on mixed-mode I and II fracture toughness of PMMA base dentures. Journal of the mechanical behavior of biomedical materials 2020; 103, 103566.

Ahmed MA, El-Shennawy M, Althomali YM, et al. Effect of titanium dioxide nano particles incorporation on mechanical and physical properties on two different types of acrylic resin denture base. World Journal of Nano Science and Engineering, 2016; 6(3), 111-119.

Al‐Harbi FA, Abdel‐Halim MS, Gad MM, et al. Effect of nanodiamond addition on flexural strength, impact strength, and surface roughness of PMMA denture base. Journal of Prosthodontics, 2019; 28(1), e417-e425.

Alhareb AO, Akil HBM, Ahmad ZAB. Poly (methyl methacrylate) denture base composites enhancement by various combinations of nitrile butadiene rubber/treated ceramic fillers. Journal of Thermoplastic Composite Materials, 2017; 30(8), 1069-1090.

Alhareb AO, Ahmad ZA. Effect of Al2O3/ZrO2 reinforcement on the mechanical properties of PMMA denture base. Journal of Reinforced Plastics and Composites, 2011; 30(1), 86-93.

Polesel A. Restoration of the endodontically treated posterior tooth. G. Ital. Endod. 28, 2–16 (2014). https://doi.org/10.1016/j.gien.2014.05.007

Daher R, Ardu S, Duc O, et al. Efficiency of 3D-printed composite resin restorations compared with subtractive materials: Evaluation of fatigue behavior, cost, and time of production. J. Prosthet. Dent. 1–8 (2022). https://doi.org/10.1016/j.prosdent.2022.08.001

Punia, U., Kaushik, A., Garg, R.K., Chhabra, D., Sharma, A.: 3D printable biomaterials for dental restoration: A systematic review. Mater. Today Proc. 63, 566–572 (2022). https://doi.org/10.1016/j.matpr.2022.04.018

Aminoroaya, A., Neisiany, R.E., Khorasani, S.N., Panahi, P., Das, O., Madry, H., Cucchiarini, M., Ramakrishna, S.: A review of dental composites: Challenges, chemistry aspects, filler influences, and future insights. Compos. Part B Eng. 216, 108852 (2021). https://doi.org/10.1016/j.compositesb.2021.108852

Chan, F.T.S., Lau, H.C.W., Ip, R.W.L., Chan, H.K., Kong, S.: Implementation of total productive maintenance: A case study. Int. J. Prod. Econ. 95, 71–94 (2005). https://doi.org/10.1016/j.ijpe.2003.10.021

Balla, V.K., Kate, K.H., Satyavolu, J., Singh, P., Tadimeti, J.G.D.: Additive manufacturing of natural fiber reinforced polymer composites: Processing and prospects. Compos. Part B Eng. 174, 106956 (2019). https://doi.org/10.1016/j.compositesb.2019.106956

Zafar, M.S.: Prosthodontic applications of polymethyl methacrylate (PMMA): An update. Polymers (Basel). 12, 1–35 (2020). https://doi.org/10.3390/polym12102299

Lohbauer, U.: Dental glass ionomer cements as permanent filling materials? -Properties, limitations and future trends. Materials (Basel). 3, 76–96 (2010). https://doi.org/10.3390/ma3010076

Somani, M.V., Khandelwal, M., Punia, V., Sharma, V.: The effect of incorporating various reinforcement materials on flexural strength and impact strength of polymethylmethacrylate: A meta-analysis. J. Indian Prosthodont. Soc. 19, 101–112 (2019). https://doi.org/10.4103/jips.jips_313_18

Jandt, K.D., Watts, D.C.: Nanotechnology in dentistry: Present and future perspectives on dental nanomaterials. Dent. Mater. 36, 1365–1378 (2020). https://doi.org/10.1016/j.dental.2020.08.006

Kumar, A., Sharma, K., Dixit, A.R.: A review of the mechanical and thermal properties of graphene and its hybrid polymer nanocomposites for structural applications. J. Mater. Sci. 54, 5992–6026 (2019). https://doi.org/10.1007/s10853-018-03244-3

Korayem, A.H., Tourani, N., Zakertabrizi, M., Sabziparvar, A.M., Duan, W.H.: A review of dispersion of nanoparticles in cementitious matrices: Nanoparticle geometry perspective. Constr. Build. Mater. 153, 346–357 (2017). https://doi.org/10.1016/j.conbuildmat.2017.06.164

Phogat, A., Chhabra, D., Sindhu, V., Ahlawat, A.: Analysis of wear assessment of FDM printed specimens with PLA, multi-material and ABS via hybrid algorithms. Mater. Today Proc. 62, 37–43 (2022). https://doi.org/10.1016/j.matpr.2022.01.429

Yadav, R., Lee, H., Lee, J.H., Singh, R.K., Lee, H.H.: A comprehensive review: Physical, mechanical, and tribological characterization of dental resin composite materials. Tribol. Int. 179, 108102 (2023). https://doi.org/10.1016/j.triboint.2022.108102

Khmich, A., Hassani, A., Sbiaai, K., Hasnaoui, A.: Tuning of mechanical properties of Tantalum-based metallic glasses. Int. J. Mech. Sci. 204, 106546 (2021). https://doi.org/10.1016/j.ijmecsci.2021.106546

Ahlawat, A., Phogat, A., Yadav, M., Sahdev, R.K., Dhingra, A.K., Chhabra, D.: Fabrication and analysis of ABS-HDPE-PC composite polymer filament used for FDM printing using hybrid algorithm. Int. J. Interact. Des. Manuf. (2023). https://doi.org/10.1007/s12008-023-01389-3

Pande, S., Chaudhary, A., Patel, D., Singh, B.P., Mathur, R.B.: Mechanical and electrical properties of multiwall carbon nanotube/polycarbonate composites for electrostatic discharge and electromagnetic interference shielding applications. RSC Adv. 4, 13839–13849 (2014). https://doi.org/10.1039/c3ra47387b

Chhabra, D., Punia, U., Gahletia, S., Garg, R.K., Sehrawat, R., Sehrawat, P., Dhingra, A., Kaushik, A.: 3D Printable NiTi Alloys for Biomedical Applications: A State of Art. Proc. - 2022 Int. Conf. Comput. Model. Simul. Optim. ICCMSO 2022. 301–306 (2022). https://doi.org/10.1109/ICCMSO58359.2022.00066

Ribeiro, D., Cimino, S.R., Mayo, A.L., Ratto, M., Hitzig, S.L.: 3D printing and amputation: a scoping review. Disabil. Rehabil. Assist. Technol. 16, 221–240 (2021). https://doi.org/10.1080/17483107.2019.1646825

Aati, S., Aneja, S., Kassar, M., Leung, R., Nguyen, A., Tran, S., Shrestha, B., Fawzy, A.: Silver-loaded mesoporous silica nanoparticles enhanced the mechanical and antimicrobial properties of 3D printed denture base resin. J. Mech. Behav. Biomed. Mater. 134, 105421 (2022). https://doi.org/10.1016/j.jmbbm.2022.105421

Della Bona, A., Cantelli, V., Britto, V.T., Collares, K.F., Stansbury, J.W.: 3D printing restorative materials using a stereolithographic technique: a systematic review. Dent. Mater. 37, 336–350 (2021). https://doi.org/10.1016/j.dental.2020.11.030

Kruzic, J.J., Arsecularatne, J.A., Tanaka, C.B., Hoffman, M.J., Cesar, P.F.: Recent advances in understanding the fatigue and wear behavior of dental composites and ceramics. J. Mech. Behav. Biomed. Mater. 88, 504–533 (2018). https://doi.org/10.1016/j.jmbbm.2018.08.008

Moshaverinia, A.: Review of the Modern Dental Ceramic Restorative Materials for Esthetic Dentistry in the Minimally Invasive Age. Dent. Clin. North Am. 64, 621–631 (2020). https://doi.org/https://doi.org/10.1016/j.cden.2020.05.002

Arunkumar, N., N. Sathishkumar, S. S. Sanmugapriya, and R. Selvam. "Study on PLA and PA thermoplastic polymers reinforced with carbon additives by 3D printing process." Materials Today: Proceedings 46 (2021): 8871-8879.

Maurya, A., Raj, A.: 5 - Recent advances in the application of biofilm in bioremediation of industrial wastewater and organic pollutants. In: Chowdhary, P., Raj, A., Verma, D., and Akhter, Y. (eds.) Microorganisms for Sustainable Environment and Health. pp. 81–118. Elsevier (2020)

Tappa, K., Jammalamadaka, U.: Novel biomaterials used in medical 3D printing techniques. J. Funct. Biomater. 9, (2018). https://doi.org/10.3390/jfb9010017


Refbacks

  • There are currently no refbacks.