Design and Development Pneumatic Operated Washer Making Machine

Authors

  • Kumbhar Rohit Bhimrao
  • Lugade Ajinakaya Rajaram
  • Mullani Kamal Dilwar
  • Patil Appaji Pundalik
  • Patil Tushar Ballu
  • Mahadev G. Reddy
  • Duradundi Sawant Badkar

DOI:

https://doi.org/10.37591/tmd.v4i3.160

Keywords:

Pneumatic operation, washer machine, fabrication, shear strength, CATIA software, design and development

Abstract

This research article presents the advanced method design and development of pneumatic operated washer making machine. The pneumatic system has gained a large amount of importance in last few decades. This project work mainly includes the main components of designs of pneumatic operated washer making machine such as: design of cylinder, selection of direction control valve, and selection of tube, design of aluminum sheet, plastic sheet, tar felt sheet and pneumatic circuit design. Design analysis also done by using CATIA software. Fabrication and implementation includes: fabrication of frame and components. This importance is due to its accuracy and cost. Due to ease of operation, handiness, and expediency in operating the pneumatic system has made us to design and fabricate this unit as our project. This pneumatic operated washer making machine unit, as we hope that it can be operated easily with partially skilled operators also. The pneumatic operated washer making machine has an advantage of working in low shear strength pressure, that is even a shear strength of 72 N/mm2 is enough for operating the unit. Different types of pneumatic operated washer making machines as requirement can be thus got. According to the work material the operating shear strength can be varied

Cite this Article

Kumbhar Rohit Bhimrao, Lugade Ajinakaya Rajaram, Mullani Kamal Dilwar et al. Design and Development Pneumatic Operated Washer Making Machine. Trends in Machine Design. 2017; 4(3): 12–20p.


Author Biographies

Kumbhar Rohit Bhimrao

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Lugade Ajinakaya Rajaram

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Mullani Kamal Dilwar

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Patil Appaji Pundalik

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Patil Tushar Ballu

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Mahadev G. Reddy

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Duradundi Sawant Badkar

Department of Mechanical Engineering, School of Mechanical Engineering, Shri Balasaheb Mane Shikshan Prasarak Mandal Ambap's, Ashokrao Mane Group of Institutions, Vathar Tarf Vadgaon, Kolhapur, Maharashtra, India

Downloads

Published

2017-12-27

Issue

Vol. 4 No. 3 (2017)

Section

Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.