Open Access Open Access  Restricted Access Subscription or Fee Access

Optimization of MRR and TWR on Electro Discharge Machining using Taguchi based GRA

Manoj Kumar Gaur, Shivani Yadav, Sharad Agrawal

Abstract


Electro Discharge Machining (EDM) is one of the most effective nonconventional machining processes in order to obtain better finishing quality result. It is vastly used to machine the most complex as well as intricate shapes so as the productivity increases in a very short time interval. The input parameters are; discharge current, voltage and pulse on time. Taguchi L9 orthogonal array is used to find out the Signal to Noise ratio by optimizing the performance parameters based upon the input parameters. The performance parameters so optimize as material removal rate, tool wear rate. Using the GREY RELATIONAL ANALYSIS, the correlation has to be draw out that makes the optimized value very accurate

Full Text:

PDF

References


Khan A. Electrode wear & material removal rate during electro discharge machining of aluminium & mild steel using copper & brass electrodes. Int J Adv Manuf Tech. 2008; 39: 482–487G.

Han F, Chen L, Yu D, et al. Int J Adv Manuf Technol. 2007; 33: 474–479p.

H. K H, Newman ST, Int J Tool Manuf. 2003; 43: 1287–1300p.

Kannan G, Subramaniam, T. Senthivelan (2012) Effect of electrode materials on EDM of 316L and 17-4PH stainless steels, J Miner Mater Character Eng. 2012; 11: 685–690p.

Koshy P, Jain VK, Lal GK. Experimental investigations into electrical discharge machining with a rotating disk electrode, Precis Eng. 1993; 15(1): 6–15p.

Yang DY, Cao FG, Liu JY, et al. The seventeenth CIRP conference on electro physical and chemical machining (ISEM), Procedia CIRP. 2013; 6: 193–1999p.

Manna A, Bhattacharyya B. Taguchi and Gauss Elimination method: A dual response approach for parametric optimization of CNC wire cut EDM of PRAISICMMC. Int J Adv Manuf Technol. 2006; 28(1): 67–75p.

Pradhan MK. Experimental investigation and modelling ofsurface integrity, accuracy and productivity aspect in EDM of AISI D2 steel. [PhD thesis], National Institute of Technology, Rourkela, 2010.

Kao P, Hocheng H. Optimization electrochemical polishing of stainless steel by grey relational analysis. J Mater Process Technol. 2003; 140(13): 255–259p.

Sharma A, Yadava V. Modeling and optimization of cut quality during pulsed Nd: YAG laser cutting of thin Al-alloy sheet for straight profile. Optics Laser Technol. 2012; 44(1): 159–168p.

Clerk Maxwell J. A Treatise on Electricity and Magnetism, 3rd ed., vol. 2. Oxford: Clarendon, 1892, 68–73p.

Jangra K, Grover S, Aggarwal A. Optimization of multi machining characteristics in WEDM of WC-5.3%Co composite using integrated approach of Taguchi, GRA and entropy method. Front Mech Eng. 2012; 7(3): 288–299p.

Al-Refaie A, Al-Durgham L, Bata N. Optimal Parameter Design by Regression Technique and Grey Relational Analysis. Proceedings of the World Congress on Engineering 2010 Vol III WCE 2010, June 30 - July 2, 2010, London, U.K.

Rao R, Yadava V. Multi-objective optimization of Nd: YAG laser cutting of thin superalloy sheet using grey relational analysis with entropy measurement. Opt Laser Technol. 2009; 41(8): 922–30p.

Lin ZC, Ho CY. Analysis and application of grey relation and ANOVA in chemical-mechanical polishing process parameters, Int J Adv Manuf Technol. 2003; 21: 10–14p.

Lo SP. The application of ANFIS and grey system method in turning tool-failure detection, Int J Adv Manuf Technol. 2002; 19: 564–572p.

CL Lin, JL, Ko TC. Optimization of the EDM process based on the orthogonal array with fuzzy logic and grey relational analysis method. Int J Adv Manuf Technol. 2002; 19: 271–277p.




DOI: https://doi.org/10.3759/joise.v3i3.3527

Refbacks

  • There are currently no refbacks.