INFLUENCE OF PULSED TIG WELDING PROCESS PARAMETERS ON MECHANICAL PROPERTIES OF ALUMINIUM ALLOY JOINT: A REVIEW

Authors

  • H. D. MAKWANA

DOI:

https://doi.org/10.3759/joise.v5i3.1533

Abstract

The increase use of aluminium alloy in the previous decades in automobile industry have recommended the research towards learning its behaviour in dissimilar condition with application. Pulsed tungsten inert gas (TIG) welding in aluminium alloy is one of the generally utilized method towards manufacturing the car parts. The present work relates to the enhancement of mechanical properties of Aluminium amalgam welds through beat tungsten latent gas (TIG) welding process. Input parameters were (weld Current, Pulsed Current, and Gas Flow Rate). The output parameters were (Tensile Strength and Shear Strength). Taguchi strategy was utilized to streamline the beat tig welding process parameters of Aluminum compound welds for expanding the mechanical properties.

 

References

Ravinder singh, sonika Chauhan, prakash Chandra gope, “Fracture Behavior of Welded Aluminum Alloy at High Strain rates’’, Elsevier, Procedia Engineering 173 (2017) 1246 – 1250

A. Kumar & S. Sundarrajan, “Effect of welding parameters on mechanical properties and optimization of pulsed TIG welding of Al-Mg-Si alloy’’, Elsevier, Int J Adv Manuf Technol (2009) 42:118–125

A. Kumar, S. Sundarrajan, “Optimization of pulsed TIG welding process parameters on mechanical properties of AA 5456 Aluminum alloy weldments’’,Elsevier, Materials and Design 30 (2009) 1288–1297

Pratik T. Kikani , Dr. Hemantkumar R. Thakkar, “A Technical review on Solidification cracking behavior and susceptibility of aluminium alloy weld’’

Tiago Vieira da Cunhaa, Anna Louise Voigt, Carlos Enrique Ni˜no Bohórquez, “Analysis of mean and RMS current welding in the pulsed TIG weldingprocess’’, Elsevier, Journal of Materials Processing Technology 231 (2016) 449–455

S. Rajakumar, C. Muralidharan, V. Balasubramanian, “Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints’’,Elsevier, Materials and Design 32 (2011) 535–549

T. Senthil Kumar, V. Balasubramanian, M.Y. Sanavullah, “Influences of pulsed current tungsten inert gas welding parameters on the tensile properties of AA 6061 aluminium alloy,Elsevier, Materials and Design 28 (2007) 2080–2092

Ji-kun DING, Dong-po Wang, Ying Wang, Hui Du, “Effect of post weld heat treatment on properties of variable polarity TIG welded AA2219 aluminium alloy joints’’,Elsevier, Trans. Nonferrous Met. Soc. China 24(2014) 1307−1316

A. K. Lakshminarayanan, V. Balasubramanian, K. Elangovan, “Effect of welding processes on tensile properties of AA6061 aluminium alloy joints’’, Int J Adv Manuf Technol (2009) 40:286–296

Sanjeev Kumar, “Experimental investigation on pulsed tig welding of aluminium plate’’, International Journal of Advanced Engineering Technology

Ahmed Khalid Hussain, Abdul Lateef, Mohd Javed, Pramesh.T, “Influence of Welding Speed on Tensile Strength of Welded Joint in TIG Welding Process’’, International journal of applied Engineering research, dindigul Volume 1, No 3, 2010

Downloads

Published

2019-01-23

Issue

Vol. 5 No. 3 (2018)

Section

Research Article

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.