Open Access Open Access  Restricted Access Subscription or Fee Access

Microstructural, Mechanical and Strengthening Mechanisms of Al7075 Metal Matrix Composite with Al2O3 Nano Particle Processed Through Ultrasonic Cavitation Assisted Stir-casting

Malleveni Shravan Kumar, Jyothula Suresh kumar, K. Chinna Maddaiah, M. Ranjith Kumar

Abstract


In this investigation, we produced Al7075 matrix composites using a stir casting method enhanced by ultra-sonic cavitation, reinforcing them with nano-Al2O3 particles. The SEM microstructural analysis confirmed the presence of nano-Al2O3 particles in all the composites, showcasing their consistent particle size and reasonably even distribution within the matrix. Optical microscopic examinations revealed that the presence of nano-Al2O3 particles, along with the aggressive ultrasonic cavitation effect, resulted in grain refinement in the matrix phase. As the quantity of nano-Al2O3 particles increased, the mechanical properties of the composites exhibited significant enhancement. Remarkably, even with only 2.0wt.% of nano-Al2O3 particle reinforcement, the manufactured composites exhibited an impressive yield strength of 134 MPa, representing a remarkable 93.3% improvement compared to the yield strength of the Al7075 matrix alloy treated solely with ultrasound. We assessed the strength of Al7075/Al2O3np composites using various models for strengthening mechanisms. Among these, the dominant contributor to strengthening was the thermal mismatch effect, followed by Orowan strengthening, the Hall-Petch mechanism, and the load transferring effect for Al7075/Al2O3np composites. The contributions from differences in coefficient of thermal expansion (CTE), interactions between dislocations in the matrix and reinforcement particles, grain refinement, and load transfer mechanisms exhibited a consistent increase with the increasing percentage of Al2O3np content within the composite.

Keywords


Al7075/ Al 2 O 3 np composites, ultrasonic cavitation assisted stir casting, mechanical properties, strengthening mechanisms

Full Text:

PDF

References


Q. Wu, W. Xu, and L. Zhang, “Machining of particulate- reinforced metal matrix composites: An investigation into the chip formation and subsurface damage,” J. Mater. Process. Technol., vol. 274, no. July, 2019.

H. Liu, D. Fu, Z. Dong, S. Huang, and H. Zhang, “Bonding interfacial characterization of SiCp/8009Al composite and A356 aluminium alloy using compound casting,” J. Mater. Process. Technol., vol. 263, no. August 2018, pp. 42–49, 2019.

S. Ji, F. Amirkhanlu, A. Mostaed, and R. Beanland, “Atomic structure and interface chemistry in a high- stiffness and high-strength Al–Si–Mg/TiB2 nanocomposite,” Mater. Sci. Eng. A, vol. 763, no. January, 2019.

M. Khan, A. Rehman, T. Aziz, M. Shahzad, K. Naveed, and T. Subhani, “Effect of inter-cavity spacing in friction stir processed Al 5083 composites containing carbon nanotubes and boron carbide particles,” J. Mater. Process. Technol., vol. 253, pp. 72–85, 2018.

K. Wang, Z. M. Zhang, T. Yu, N. J. He, and Z. Z. Zhu, “The transfer behaviour in centrifugal casting of SiCp/Al composites,” J. Mater. Process. Technol., vol. 242, pp. 60– 67, 2017.

R. Dasgupta, “Aluminium Alloy-Based Metal Matrix Composites: A Potential Material for Wear Resistant Applications,” ISRN Metall., vol. 2012, pp. 1–14, 2012.

T. B. Rao, “An Experimental Investigation on Mechanical and Wear Properties of Al7075/SiCp Composites: Effect of SiC Content and Particle Size,” J. Tribol., vol. 140, no. 3, p. 031601, 2017.

S. Lü, P. Xiao, D. Yuan, K. Hu, and S. Wu, “Preparation of Al matrix nanocomposites by diluting the composite granules containing nano-SiCp under ultrasonic vibaration,” J. Mater. Sci. Technol., vol. 34, no. 9, pp. 1609– 1617, 2018.

Y. Yang, J. Lan, and X. Li, “Study on bulk aluminium matrix nano-composite fabricated by ultrasonic dispersion of nano-sized SiC particles in molten aluminium alloy,” Mater. Sci. Eng. A, vol. 380, no. 1, pp. 378–383, 2004.

D. Yuan, K. Hu, S. Lü, S. Wu, and Q. Gao, “Preparation and properties of nano-SiC p / A356 composites synthesised with a new process,” vol. 0836, 2018.

B. Pu, X. Lin, B. Li, X. Chen, C. He, and N. Zhao, “Effect of SiC nanoparticles on the precipitation behaviour and mechanical properties of 7075Al alloy,” J. Mater. Sci., vol. 55, no. 14, pp. 6145– 6160, 2020.

K. Amouri, S. Kazemi, A. Momeni, and M. Kazazi, “Microstructure and mechanical properties of Al- nano/micro SiC composites produced by stir casting technique,” Mater. Sci. Eng. A, vol. 674, pp. 569– 578, 2016.

R. Soundararajan, S. Sivasankaran, N. Babu, and G. P. R. Adhithya, “Appraisal of tribological properties of A356 with 20% SiC composites under dry sliding condition,” J. Brazilian Soc. Mech. Sci. Eng., vol. 42, no. 3, pp. 1–12, 2020.

J. Zhu, W. Jiang, G. Li, F. Guan, Y. Yu, and Z. Fan, “Microstructure and mechanical properties of SiCnp/Al6082 aluminium matrix composites prepared by squeeze casting combined with stir casting,” J. Mater. Process. Technol., vol. 283, no. March, p. 116699, 2020.

P. Maji, S. K. Ghosh, R. K. Nath, and R. Karmakar, “Microstructural, mechanical and wear characteristics of aluminium matrix composites fabricated by friction stir processing,” J. Brazilian Soc. Mech. Sci. Eng., vol. 42, no. 4, pp. 1–24, 2020.

A. Premnath, “Optimization of the Process Parameters on the Mechanical and Wear Properties of Al-SiC Nano- Composites Fabricated by Friction Stir Processing Using Desirability Approach,” Silicon, vol. 12, no. 3, pp. 665–675, 2020.

L. Poovazhagan, K. Kalaichelvan, and A. Rajadurai, “Preparation of SiC nano-particulates reinforced aluminium matrix nanocomposites by high intensity ultrasonic cavitation process,” Trans. Indian Inst. Met., vol. 67, no. 2, pp. 229–237, 2014.

S. sen Wu, D. Yuan, S. lin Lü, K. Hu, and P. An, “Nano- SiCP particles distribution and mechanical properties of Al- matrix composites prepared by stir casting and ultrasonic treatment,” China Foundry, vol. 15, no. 3, pp. 203–209, 2018.

A. Prasad Reddy, P. Vamsi Krishna, and R. N. Rao, “Tribological Behaviour of Al6061–2SiC-xGr Hybrid Metal Matrix Nanocomposites Fabricated through Ultrasonically Assisted Stir Casting Technique,” Silicon, vol. 11, no. 6, pp. 2853–2871, 2019.

A. H. Idrisi and A. H. I. Mourad, “Conventional stir casting versus ultrasonic assisted stir casting process: Mechanical and physical characteristics of AMCs,” J. Alloys Compd., vol. 805, pp. 502– 508, 2019.

Q. Li et al., “Fabrication, microstructure refinement and strengthening mechanisms of nanosized SiCP/Al composites assisted ultrasonic vibration,” Mater. Sci. Eng. A, vol. 735, pp. 310–317, 2018.

M. Tavoosi, F. Karimzadeh, M. H. Enayati, and A. Heidarpour, “Bulk Al-Zn/Al2O3 nanocomposite prepared by reactive milling and hot pressing methods,” J. Alloys Compd., vol. 475, no. 1–2, pp. 198– 201, 2009.

D. Yuan, X. Yang, S. Wu, S. Lü, and K. Hu, “Development of high strength and toughness nano- SiCp/A356 composites with ultrasonic vibration and squeeze casting,” J. Mater. Process. Technol., vol. 269, pp. 1–9, 2019.

X. Li, Y. Yang, and X. Cheng, “Ultrasonic-assisted fabrication of metal matrix nanocomposites,” J. Mater. Sci., vol. 39, no. 9, pp. 3211–3212, 2004.

L. J. Zhang, F. Qiu, J. G. Wang, and Q. C. Jiang, “High strength and good ductility at elevated temperature of nano- SiCp/Al2014 composites fabricated by semi-solid stir casting combined with hot extrusion,” Mater. Sci. Eng. A, vol. 626, pp. 338–341, 2015.

[G. Cao, H. Konishi, and X. Li, “Mechanical properties and microstructure of Mg/SiC nanocomposites fabricated by ultrasonic cavitation based nanomanufacturing,” J. Manuf. Sci. Eng. Trans. ASME, vol. 130, no. 3, pp. 0311051–0311056, 2008.

Q. Gao, S. Wu, S. Lü, X. Xiong, R. Du, and P. An, “Improvement of particles distribution of in- situ 5 vol% TiB2particulates reinforced Al-4.5Cu alloy matrix composites with ultrasonic vibration treatment,” J. Alloys Compd., vol. 692, pp. 1–9, 2017.

G. I. Eskin and D. G. Eskin, “Production of natural and synthesized aluminium-based composite materials with the aid of ultrasonic (cavitation) treatment of the melt,” Ultrason. Sonochem., vol. 10, no. 4–5, pp. 297–301, 2003.

K. HU, D. YUAN, S. lin LÜ, and S. sen WU, “Effects of nano-SiCp content on microstructure and mechanical properties of SiCp/A356 composites assisted with ultrasonic treatment,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 28, no. 11, pp. 2173–2180, 2018.

S. Jia, D. Zhang, Y. Xuan, and L. Nastac, “An experimental and modeling investigation of aluminium- based alloys and nanocomposites processed by ultrasonic cavitation processing,” Appl. Acoust., 2015.

J. Jiang and Y. Wang, “Microstructure and mechanical properties of the semisolid slurries and rheoformed component of nano-sized SiC/7075 aluminium matrix composite prepared by ultrasonic- assisted semisolid stirring,” Mater. Sci. Eng. A, vol. 639, pp. 350–358, 2015.

J. Jiang, Y. Wang, X. Nie, and G. Xiao, “Microstructure evolution of semisolid billet of nano-sized SiCp/7075 aluminium matrix composite during partial remelting process,” Mater. Des., vol. 96, pp. 36–43, 2016.

J. Li, S. Lü, S. Wu, W. Guo, and F. Li, “Variation of microstructure and mechanical properties with nano- SiCp levels in the nano-SiCp/AlCuMnTi composites,” J. Alloys Compd., vol. 769, pp. 848– 857, 2018.

J. Li, S. Lü, S. Wu, and Q. Gao, “Effects of ultrasonic vibration on microstructure and mechanical properties of nano-sized SiC particles reinforced Al-5Cu composites,” Ultrason. Sonochem., vol. 42, pp. 814–822, 2018.

Y. Yang and X. Li, “Ultrasonic cavitation based nanomanufacturing of bulk aluminium matrix nanocomposites,” J. Manuf. Sci. Eng. Trans. ASME, vol. 129, no. 3, pp. 497–501, 2007.

S. Song, X. Zhou, L. Li, and W. Ma, Numerical simulation and experimental validation of SiC nanoparticle distribution in magnesium melts during ultrasonic cavitation based processing of magnesium matrix nanocomposites, vol. 24. 2015.

Y. Yang, J. Lan, and X. Li, “Study on bulk aluminium matrix nano-composite fabricated by ultrasonic dispersion of nano-sized SiC particles in molten aluminium alloy,” Mater. Sci. Eng. A, vol. 380, no. 1, pp. 378–383, 2004.

M. Kouzeli and A. Mortensen, “Size dependent strengthening in particle reinforced aluminium,” Acta Mater., vol. 50, no. 1, pp. 39–51, 2002.

[B. Q. Han and D. C. Dunand, “Microstructure and mechanical properties of magnesium containing high volume fractions of yttria dispersoids,” Mater. Sci. Eng. A, vol. 277, no. 1–2, pp. 297–304, 2000.

L. Poovazhagan, K. Kalaichelvan, and T. Sornakumar, “Processing and Performance Characteristics of Aluminium-Nano Boron Carbide Metal Matrix Nanocomposites,” Mater. Manuf. Process., vol. 31, no. 10, pp. 1275–1285, 2016.

N. Kumar, G. Gautam, R. K. Gautam, A. Mohan, and S. Mohan, “A Study on Mechanical Properties and Strengthening mechanisms of AA5052/ZrB2 in Situ Composites,” J. Eng. Mater. Technol. Trans. ASME, vol. 139, no. 1, pp. 1–8, 2017.

J. Nampoothiri, I. Balasundar, T. Raghu, and K. R. Ravi, “Structural and Mechanical Behaviour of Al- 4.4Cu/2TiB2 In-Situ Nanocomposites Fabricated by Post- In-Situ Reaction Ultrasonic Processing,” Metall. Mater. Trans. B Process Metall. Mater. Process. Sci., vol. 51, no. 1, pp. 149– 160, 2020.

R. Raj, “Effect of particle size and volume fraction on the strengthening mechanisms of boron carbide reinforced aluminium metal matrix composites,” vol. 0, no. 0, pp. 1– 12, 2018.

F. Chen, Z. Chen, F. Mao, T. Wang, and Z. Cao, “Materials Science & Engineering A TiB 2 reinforced aluminium based in situ composites fabricated by stir casting,” Mater. Sci. Eng. A, vol. 625, pp. 357–368, 2015.

P. Hauschwitz et al., “Hydrophilic to ultrahydrophobic transition of Al 7075 by affordable ns fiber laser and vacuum processing,” Appl. Surf. Sci., vol. 505, p. 144523, 2020.

R. Manikandan, T. V. Arjunan, and A. R. Akhil, “Studies on micro structural characteristics, mechanical and tribological behaviours of boron carbide and cow dung ash reinforced aluminium (Al 7075) hybrid metal matrix composite,” Compos. Part B Eng., vol. 183, no. Al 7075, p. 107668, 2020.

J. Hashim, L. Looney, and M. S. J. Hashmi, “The enhancement of wettability of SiC particles in cast aluminium matrix composites,” J. Mater. Process. Technol., vol. 119, no. 1–3, pp. 329–335, Dec. 2001.

H. Su, W. Gao, H. Zhang, H. Liu, J. Lu, and Z. Lu, “Optimization of Stirring Parameters Through Numerical Simulation for the Preparation of Aluminium Matrix Composite by Stir Casting Process,” J. Manuf. Sci. Eng., vol. 132, no. 6, p. 061007, 2010.

H. Xu, X. Jian, T. T. Meek, and Q. Han, “Degassing of molten aluminium A356 alloy using ultrasonic vibration,” Mater. Lett., vol. 58, no. 29, pp. 3669–3673, 2004.


Refbacks

  • There are currently no refbacks.