Comparative Study of RC Elevated Water Tank

Authors

  • Sanket Kiranrao Doke
  • S.B. Deshmukh

DOI:

https://doi.org/10.37591/josem.v10i3.7368

Abstract

Designing a water tank requires a good approximation of water demands which is depends on the estimation of population growth rate and design life of the tank and the per capita water consumption rate. Due to rapid increase in urbanization, development activities and enormous need by the public the rate of water consumption increasing day by day. It would difficult task to supply the water directly from the source, it should be stored and treated. In this paper we are analyzing the elevated circular and intze water tank by using Staad Pro. After conducting a manual analysis and design of water parameters, the findings extracted from all the final graphs lead us to the conclusion that, in comparison to elevated circular water tanks, elevated Intze water tanks exhibit lower moment values. This observation indicates that the elevated Intze water tank design is more economical and potentially offers cost savings.

References

Nibedita Sahoo, S.k. Sahoo (2008) “Design of Water Tank” Department of civil engineering

National Institute of Technology Rourkela.

S. Ramamrutham (2014) “Design of Reinforced Concrete Structure” Dhanpat Rai 1682, Naisarak,

delhi – 110006

Mani Mohan (2015) “Analysis and Design of Elevated RCC Water Tank Structure” Department of

Civil Engineering Jaypee University of Information Technology, waknaghat.

Neha. S. Vanjari, krutika, M. Sawant, Prashant. S. Sisodiya, S.B. Patil (2017) “Design of Circular

Overhead Water Tank” International Journal of Engineering Research in Mechanical and Civil

Engineering (IJERMCE) Vol 2, Issue 7.

Mohammed Azgar, N.Ramya Smruthi (2017) “Design of Circular Water Tank Using Staad pro

Software “ International Journal of Scientific Engineering and Technology Research ISSN 2319-

Vol 6, Issue 29.

Manoj Nallanathel, B. Ramesh, L. Jagadeesh (2018) “Design and Analysis of Water Tanks Using

Staad Pro” International Journal of Pure and Applied Mechanics Volume 119 NO.17.

Issar Kapadia, Purva Patel, Nilesh Dholia and Nikunjan Patel (2018) “Design and analysis of water

tank using staad pro” Vol 119 No.17.

Mainak Ghosal (2019) “Analysis and Computational Design of Water Tank Structure” Indian

Institute of Engineering Science and Technology, Shibpur.

M.L. Gambhir (2008) edition of “Designed of Reinforced Concrete Structures”.

Chandana Imadabathuni, Nallla Ravi Kiran, Bathula Naveeen (2021) “Analysis and Design of Intze

water tank by using Staad Pro”.

IS 456 – 2000: Code of practice for Plain and reinforced Concrete, Plain and reinforced Concrete

code of practice, Bureau of Indian standards manak bahvan, 9 Bahadur Shah Zafar Marg New Delhi

IS 875 –1987: (Part 2) Code of practice Design Loads for building and structures Bureau of Indian

standards manak bahvan, 9 Bahadur Shah Zafar Marg New Delhi 110002

IS 3370 -2009: (Part 1 & Part 2) Code of Practice for Concrete Structures for Storage of liquids:

General Requirements.

IS 3370 -1967: (Part 4) Design tables for design of Reinforced or Prestressed Concrete structures

for storage of liquids.

Downloads

Published

2023-09-27

Issue

Vol. 10 No. 3 (2023)

Section

Research Article

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.