Open Access
Subscription or Fee Access
Three-phase squirrel cage induction motor employing PLC-based Star-Delta starter
Abstract
This presentation discusses the significance of regulating beginning current and torque while finally beginning a motor. A multiple doubly fed induction motor may be started using a variety of methods. In addition, a star-delta technique utilising a reconfigurable controller (PLC) is described and evaluated to begin the Actuator Throughout the beginning process of a squirrel cage induction motor, the predominant and start contactors remain suspended and establish the circuit. This same supply voltage is reduced to one-third of the center frequency through each circuit during the Star startup phase, resulting in a lower starting current. After a brief span of time, mechanical timer linked to the initiator first connection problems the star contactor and then reconnects the delta contactor when the motor has rotated at around 90% of its maximum rpm. It thus enables the device to start at maximum load voltage without issue. The PLC controls the method of managing time and regulating contactors. The output of the Controller should be utilised to activate the condensers. The construction and execution of a three-phase star-delta going to begin combustion engine utilising a PLC is addressed and demonstrated in this study. Mechanisation is enhanced by the PLC's flexibility and excellent controllability.
References
Sanjiv Kumar, Devendra Kumar, Vikash Saini, Jitendra Kumar, “Industrial Automation System”, XXXII National Conference, NSC 2008, December 17–19, 2008; Indian Institute of Technology. Roorkee.
Avvaru Ravi Kiran, Ch. Sree Vardhan, B. Venkat Sundeep, Neel Mathews. “The Principle of Programmable Logic Controller and its role in Automation”, International Journal of Engineering Trends and Technology. 2013; 4(3):500–502.
K Gowri Shankar, “Control of Boiler operation using PLC-SCADA”, Proceedings of the International Multi Conference of Engineers and Computer Scientists. 2008; II, IMECS 2008, 19–21 March, 2008, Hong Kong.
Maria G. Ioannides, “Design and Implementation of PLC-Based Monitoring Control System for Induction Motor”, IEEE Transactions on Energy Conversion. September 2004; 19(3): 469–476.
Richard A. Cox, “Technician’s guide to Programmable Controllers”. 6th Edition. Delmar Cengage Learning. 2012.
Sadegh vosougp, Amir vosougp. “PLC and its applications”. International Journal of Multidisciplinary Sciences and Engineering. November 2011; 2(8): 41–46.
Nidhi Phadnis, Shruti Kharait, Devesh Tamrakar, Sudhir Pulambrikar. “PLC and its applications to control single phase induction motor”. International Journal of Engineering Sciences & Management. July-September 2013; 3(3): 36–41.
Saurabh Sharma, T.Y. Ladakhi, A.P. Tiwary, R. Phipon, B.B. Pradhan. “Application of PLC for Elevator Control System” International Symposium on Devices MEMS, Intelligent Systems & Communication (ISDMISC) 2011 Proceedings published by International Journal of Computer Applications (IJCA). 1–7 p
Jamnani J.G, “ Elements of Electrical Design”, Mahajan Publications, 2015, 4th Edition. chap-3, pp. 3.1–3.20.5
W. Bolton, “Programmable logic controllers”, fifth edition, Linacre House, Jordan Hill, Oxford OX2 8DP UK, 2009.
Shruti Kharait, Prof. Sudhir Phulambrikar. “Implementation of PLC Based Star Delta Starter for Starting and Direction Control of Three Phase Induction Motor”. International Journal of Engineering Research & Technology. November 2013; 2(11).
Akshay P. Shinde, Kiran S. Shendge, Ranjit K. More, Prashant B. Pawar. “PLC Automation of star delta starter for using induction motor”. International Journal For Technological Research In Engineering. May 2017; 4(9): 1673–1677.
Saurabh Sharma and T.Y.Ladakhi , Assistant Professor-II Mech. Engg. Dept SMIT, Majitar, A.P. Tiwary and R. Phipon, Associate Professor Mech. Engg. Dept SMIT, Majitar, Dr. B.B. Pradhan Professor Mech. Engg. Dept SMIT, Majitar, “Application of PLC for Elevator Control System” International Symposium on Devices MEMS, Intelligent Systems & Communication (ISDMISC). 2011 Proceedings published by International Journal of Computer Applications (IJCA).
B.I.Aldi, J.S. Kadadevarmath, N.P. Bannibagi. “Design and implementation of a PLC based Electrical supply switching control system”. IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE. May–June 2016; 11(3) Ver. III: 43–50.
Deepali S. Shirke, Haripriya, H.Kulkarni. “Microcontroller based speed control of three phase induction motor using v/f method”. International Journal of Scientific and Research Publications. February 2013; 3(2): 1–6.
Yasar Birbir, H.Selcuk Nogay, “Design and Implementation of PLC-Based Monitoring Control System for Three-Phase Induction Motors Fed by PWM Inverter”. International Journal of Systems Applications, Engineering & Development. 2008; 2(3): 128–135.
Ali Gulabi. “Development of an Embedded SCADA System with PLC and Java Application for Synchronous Operation of Standard Servo Drives”, Master thesis Faculty of Engineering and Computer Science of the University of Applied Sciences Hamburg, May 2007.
Rinchen Geongmit Dorjee, “Monitoring and Control of a Variable Frequency Drive Using PLC and SCADA”, International Journal on Recent and Innovation Trends in Computing and Communication. October 2014; 2 (10): 3092–3098.
S. Green, D.J. Atkinson, A.G. Jack B.C. Mecrow, A. king. ‟Sensorless operation of a fault tolerant PM drive”. IEEE Proceedings-Electric Power Applications. 2003; 39(5): 2962–2964.
J.B. Wang, K. Atallah, and D. Howe, “Optimal torque control of fault-tolerant permanent magnet brushless. IEEE Transactions on Magnetics. September 2003; 39(5): 2962–2964.
Refbacks
- There are currently no refbacks.
Copyright (c) 2022 Trends in Electrical Engineering
eISSN: 2249-4774