Regulation of Second and third Order Intervals Plant Using PID Surface Sliding Mode Control Strategy

Authors

  • chitturi vijay kumar M.tech Scholar, Department, Electrical of Engineering, Andhra university, Visakhapatnam, Andhra Pradesh, India
  • B. Amarendra Reddy Assistant Professor, Department, Electrical of Engineering, Andhra university, Visakhapatnam, Andhra Pradesh, India
  • Ch. Nayak bhukya PhD Scholar, Department, Electrical of Engineering, Andhra university, Visakhapatnam, Andhra Pradesh, India

DOI:

https://doi.org/10.37591/.v13i2.7382

Abstract

In this article regulation aspects of second and third-order interval systems considering sliding mode control, PID surface sliding mode control strategies are discussed. The transfer function models of second and third order systems are considered for the evaluation of system performances. The linear part and non-linear part of the SMC strategy are designed and stability is analyzed using Lyapunov analysis. A conventional PID controller and PID surface SMC strategy are also designed for regulation of these interval plants. A DC motor interval system is considered as a special case of second -order system and the three types of controllers are also designed for this system. The steady-state and transient performance of these closed-loop interval plants are verified in the MATLAB environment.

References

B. A. Reddy and P. V. Krishna, "Traditional and 2-SMC Control Strategies for Coupled Tank System," 2019 Third International Conference on Inventive Systems and Control (ICISC), Coimbatore, India, 2019, pp. 682-687, doi: 10.1109/ICISC44355.2019.9036440. (references)

K. Anusha, B. A. Reddy, A. R. Gopisetti and B. P. Kumar, "Higher Order Sliding Mode Control and Performance Evaluation of DC Motor Under Parameter Variations," 2018 International Conference on Current Trends towards Converging Technologies (ICCTCT), Coimbatore, India, 2018, pp. 1-7, doi: 10.1109/ICCTCT.2018.8551163.

M. A. Hassanin, F. E. Abdel-Kader, S. I. Amer, and A. E. AbuMoubarka, “Operation of Brushless DC Motor to Drive the Electric Vehicle,” in 2018 20th International Middle East Power Systems Conference, MEPCON 2018 - Proceedings, 2019, pp. 500–503.

P. Vishnu Sidharthan and Y. Kashyap, “Brushless DC hub motor drive control for electric vehicle applications,” in 2020 1st International Conference on Power, Control and Computing Technologies, ICPC2T 2020, 2020, pp. 448–453.

V. Yadav and V. K. Tayal, “Optimal Controller Design for a DC Motor using PID Tuner,” in 2018 International Conference on Power Energy, Environment and Intelligent Control, PEEIC 2018, 2019, pp. 442–445.

R. V. Jain, M. V. Aware, and A. S. Junghare, “Tuning of Fractional Order PID controller using particle swarm optimization technique for DC motor speed control,” in 1st IEEE International Conference on Power Electronics, Intelligent Control and Energy Systems, ICPEICES 2016, 2017.

I. S. Okoro and C. O. Enwerem, “Robust control of a DC motor,” Heliyon, vol. 6, no. 12, Dec. 2020.

J. Yang, S. Li, and X. Yu, “Sliding-mode control for systems with mismatched uncertainties via a disturbance observer,” IEEE Transactions on Industrial Electronics, vol. 60, no. 1, pp. 160–169, 2013.

M. Zhou, D. Mao, M. Zhang, L. Guo, and M. Gong, “A Hybrid Control with PID–Improved Sliding Mode for Flat-Top of Missile Electromechanical Actuator Systems,” Sensors, vol. 18, no. 12, p. 4449, Dec. 2018.

A. A. Al Rawi, R. B. Ahmad, and H. H. Tahir, “Chatter-less slidingmode controller for DC motor”, in Proc. IEEE Student Conf. Research and Development, Putrajaya, 2013, pp. 54–59. DOI: 10.1109/SCOReD.2013.7002540.

S. Kurode, B. Tamhane, Dharmveer, and P. Dixit, “Robust control with simultaneous state and disturbance estimation using sliding modes”, in Proc. 12th International Workshop on Variable Structure Systems (VSS), Mumbai, Maharashtra, 2012, pp. 237–242. DOI: 10.1109/VSS.2012.6163508.

Downloads

Published

2023-10-19

Issue

Vol. 13 No. 2 (2023)

Section

Articles

License

Journal Title:

Title of the Paper:

Corresponding Author’s Information:

Name: Address:

E-mail:

Contact Number:

It is herein agreed that: The copyright to the above-listed unpublished and original article is transferred to STM Journals.

This copyright transfer covers the exclusive right to reproduce and distribute the contribution, including reprints, translations, photographic reproductions, microform, electronic form (offline, online), or any other reproductions of similar nature.

I/We declare that above manuscript is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

 I/ We warrant(s) that his/her/their contribution is original, except for such excerpts from copyrighted works as may be included with the permission of the copyright holder and author thereof, that it contains no libelous statements, and does not infringe on any copyright, trademark, patent, statutory right, or propriety right of others.

I/We will not publish his/her/their above said contribution anywhere else without the prior written permission of the publisher unless it has been changed substantially. I/We also agree to the authorship of the article in the following order: Author(s) Name Signature(s)

1. ________________

2. ________________

3. ________________

4. ________________

The author(s) agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal (comments if any to the editor can be added below).