Design and Fabrication of Rubber Shredder Machine

Authors

  • Palani Kumar D Assistant Professor, Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Tamil Nadu, India
  • Prem Kumar V.V Under Graduate Student, Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Tamil Nadu, India
  • Thirumalaira J.K. Under Graduate Student, Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Tamil Nadu, India
  • Shanmugasundharam M. Under Graduate Student, Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Tamil Nadu, India
  • Narayanasamy P Associate professor, Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Tamil Nadu, India

DOI:

https://doi.org/10.37591/tmet.v13i3.7634

Keywords:

Design optimization, waste management, shredding machine, recycle, fabrication

Abstract

Rubber waste has become a significant environmental challenge, and the development of a rubber shredder machine is an important initiative aimed at reducing rubber waste by shredding it into tiny pieces for recycling or repurposing. This project involves designing, fabricating, and testing a rubber shredder machine to address the challenges associated with rubber waste. The machine is designed to shred rubber materials into tiny pieces, which can be further processed for recycling or repurposing. The project aims to create an efficient, safe, and effective machine that can contribute to the efforts to promote sustainable practices and reduce waste. The successful fabrication of a rubber shredder machine requires careful consideration of the required specifications, selection of appropriate materials, and careful assembly and testing to ensure optimal performance. The project has the potential to make a significant contribution to the global effort to reduce waste and promote sustainable practices.

References

Dr Jan Melichercik, Crusher for plastic,2021. Describes the stress and strain analysis of the cutting devices of the crusher using a defined material for its production.

Kumar (2019), the authors discussed the importance of rubber recycling and the role of shredder machines in this process.

Singh (2018), describes the use of a rubber shredder machine to reducing the size of the rubber waste and producing a consistent shredded product.

Al-Mutairi (2016), use of a rubber shredder machine in processing rubber waste generated by a tire manufacturing plant.

Yeshwant M. sonkhaskar, Amit choubey, Amritpal bhamra, and etc.…, crusher for bottle, (2010) Design of a plastic bottle crusher, Explains about design of a plastic crusher which would help to crush the used plastic bottle and would help in waste management.

Nagarajan N, Srinivasan S, Balathilaka, crusher for cans (2019). Describes about design of a can crusher and defined material for its production.

Makinde-Ojo, Ayoola macjay ,2016. Describes the design and analysis of sugarcane juice machines.

Design and Development of Plastic Shredding Machine.Mulla Irfan Faiyyaj, Mete Rushabh Pradip, Bhosale Jaydeep Dhanaji, Dange Prasad Chandrashekhar, Jadhav Suraj Shivaji

Plastic Waste Management By Mechanical Shredder Machine Akash. B. P, Christina, Darshan. K. S, Manoj

Research on shredding process and characteristics of multi-material plates for recycled cars by Xianyan Zhou, Zhili Hu, Xiang Xiao and Mingbo Li

Downloads

Published

2024-02-06

Issue

Vol. 13 No. 3 (2023)

Section

Review Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.