Open Access
Subscription or Fee Access
Design and Analysis of Master Cylinder and Caliper using Solid Works and Ansys
Abstract
Safety is a very important aspect of the vehicle. Effective Braking system along with good suspension systems and good handling is very important for determining the performance of the vehicle. This work deals with the study of the existing braking components, like master cylinder and caliper, designing of new braking components using SOLIDWORKS, and to perform static structural analysis on ANSYS .The objective of the newer designs is to increase the braking power and reduce the stopping distance without causing much change to the parameters like total deformation, principal stresses, shear stresses, factor of safety and weight. The analysis was done on master cylinder and caliper using ANSYS workbench. . The standard dimensions of master cylinder are taken from MARUTI 800, while that of caliper is taken from the Bajaj Pulsar.The results are plotted in tabular format.
Keywords
References
Gs.Patil1, G.Bhanu Prakash , M.Narsimula:”Modeling and Analysis of a Brake Caliper” Research Inventry: International Journal of Engineering And Science Vol.5, Issue 8 (August
, PP -31-36 Issn (e): 2278-4721, Issn (p):2319,
K. Dalal, A. Karnik: “Monoblock brake caliper design and analysis” International Research Journal of Engineering and Technology (IRJET), Volume: 07 Issue: 08 | Aug 2020 www.irjet.net.
V. Saibabu, G. Vijaya Prakash: “Design and Structural Analysis of Master Cylinder for Pressure Loads” ISSN 2321-8665 Volume.06, Issue.01, January-June, 2018,Pages:0292-0296.
N. P. Wagh: “Design And analysis of Break Caliper”,Bachelor of Engineering, Shivaji University, 2000. Submitted to the College of Engineering and the faculty of the Graduate School of Wichita State University in partial fulfillment of
the requirements for the degree of Master of Science, December 2005.
S. Konda, M. Kapse, V. Wankhade, M. Bhure, A. Thosar: “Design and Analysis of a Master Cylinder for Hydraulic Breaking System”, International Journal of Automobile Engineering Research and Development (IJAuERD) ISSN (P):
–4785; ISSN (E): 2278–9413 Vol. 9, Issue 2, Dec 2019, 11–22.
J. Reddaiah, G. Harinath Gowd, S. Praveen Kumar, V. Vishnuvardhan: “Design & Analysis of Master Cylinder of Hydraulic Braking System using ANSYS”,International Journal of Innovative Technology and Exploring Engineering (IJITEE) ,ISSN: 2278-3075, Volume-3 Issue-7, December 2013.
D. Phad, T. Auti, R. Joshi, S. Jadhav, S.Devasthali: “Design and analysis of a brake caliper”, International Journal of Automobile Engineering Research and Development (IJAuERD) ISSN(P): 2277-4785; ISSN(E): 2278-9413 Vol. 5,
Issue 5, Oct 2015, 1-10.
Dr. A. Satyanarayana Reddy, S.M. Mohiddin : “Design and Analysis of Master Cylinder and caliper”,IJSTE -International Journal of Science Technology & Engineering | Volume 3 | Issue 08 | February 2017 ISSN (online): 2349-784X
P. M. Patel, S. Sudheendra.: “Design and Analysis of Titanium Caliper Disc Brake”,2017 IJEDR | Volume 5, Issue 1 | ISSN: 2321-9939
B. Sandhya Rani, K. Prabhakar, C. Mohan Naidu : “Design andAnalysis of Plastic Brake Master”Cylinder for Automobiles ISSN: 2277- 3754,ISO 9001:2008 Certified,International Journal of Engineering and Innovative Technology
(IJEIT),Volume 4, Issue 2, August 2014.
S. Royzada: “Design and Analysis of Braking System of An ATV with Efficient Wheel Locking and Weight Reduction”, International Journal of Engineering Research & Technology (IJERT) ISSN: 2278-0181,Vol. 9 Issue 07, July-2020.
R. Shah, C. Shah: “Design and analysis of a hydraulic brake caliper”International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 33–41, ArticleID: IJMET_08_05_004 http://www.iaeme.com/IJMET/issues.asp?JType=IJ MET&VType=8&IType=5 ISSN Print: 0976-6340 and ISSN Online: 0976-6359.
Miss. P. B. Sawant, Prof. P.D. Kale: “Force and Friction analysis of disc brake of two wheeler”, Proceedings of the ASME 2014 Gas Turbine India Conference GTINDIA2014- 8352, December 15-17, 2014, New Delhi, India
Mr. S. Chavan, Mr. V. Tile , Mr. M. Chavhan , Mr. S. Agnihotri: “Design and Analysis of Brake master cylinder for an ATV”, August 2018 | IJIRT | Volume 5 Issue 3 | ISSN: 2349-6002 .
Brake Testing Methodology Study - Driver Effects Testing, U.S department of Transportation.
P. M. Patel, Sudheendra S: “Design and Analysis of Titanium Caliper Disc Brake”, © 2017 IJEDR | Volume 5, Issue 1 | ISSN: 2321-9939 .
P. Liu a, H. Zheng a, C. Cai a, Y.Y. Wang a, C.Lu a,K.H. Ang b, G.R. Liu, Analysis of disc brake squeal using the complex eigenvalue method, ScienceDirect, Applied Acoustics 68 (2007) 603–615.
V.M.M. Thilak, R. Krishnaraj, Dr.M. Sakthivel, K. Kanthavel, D. Marudachalam, M.G. Palani , Transient Thermal and Structural Analysis 8 of the Rotor Disc of Disc Brake ,InternationalJournal of Scientific & Engineering Research, Volume 2, Issue 8, August -2011 ISSN 2229-5518
M. Nouby, D. Mathivanan, K. Srinivasan, A combined approach of complex eigenvalue analysis and design of experiments (DOE) to study disc brake squeal, International Journal of Engineering, Science and Technology Vol. 1, No. 1, 2009, pp. 254-271.
Khan T.A., Yadav, A.K, Khan, T.A., Khan M.E. Microalgae: A Promising Third Generation Renewable Energy Source for I.C. Engines , Journal of Automobile Engineering and Applications, (2020) vol.7 issu 1;1-5,
AK Yadav, A Pal, ME Khan. Optimization of Production and Performance of Biodiesel through Optimization Techniques: A Review, International Journal of Advance Research and Innovation, Vol.2, Issue 4 (2014) 763-766
AK Yadav, S Singh, G Gupta, Solar Air- Conditioning: Design for a Compressor-Less System using, Peltier Effect, International Journal of Advance Research and Innovation, Volume 2, Issue 2 (2014) 429-432
AK Yadav, Optimum Production of Biodiesel from an Underutilized and Potential Feed stock, Kusum Seed Oil., Iranica Journal of Energy and Environment 8(1): 6-10, 2017
AF Sherwani, AK Yadav, MN Karimi, Experimental study on the performance and emission Characteristics of a four stroke diesel engine Running with mahua oil ethyl ester. Int. Journal of Sust. development and green economics
(2013), Vol. 2, pp. 80-84
AF Sherwani, A Sharma, AK Yadav, Comparative Analysis of Performance and Emission Parameters of A C.I. Engine Fuelled With Different Blends Of Biodiesel Derived From Mahua Oil And Waste Cooking Oil. Int. Journal of Innov. Research in Science, Engg & Tech. (2013) 2 (9) : 944-52
O Khan, ME Khan, A Kumar, S Kumar, Study on Some Advanced Techniques to Produce Biodiesel from Non-edible Oils, International Journal of Advance Research and Innovation,Vol. 5, Issue 1 (2017) 34-38
A Malviya, AK Bera, MD Pandey, L Gupta, P Gautam, A Kumar, Production of biodiesel from mahua oil by mechanical stirring and its performance testing on a diesel engine, International Journal of Advance Research and Innovation, Volume 5 Issue 3 (2017) 372-375
AK Yadav, S Singh, U Ghosh, G Gupta, Design and Manufacturing of Honing Tool for Drilling Machine, International Journal of Advance Research and Innovation Volume 2, Issue 2 (2014) 433-435
S Singh, AK Yadav, B Singh, Thermal Energy Harvesting using BaTiO3 Based Ferroelectric Ceramics: A Review, International Journal of Advance Research and Innovation, Volume 6, Issue 3(2018) 209-211
N. Kumar, A. K. Yadav, A. Dewangan, and M. Kumar, CFD Based Investigation of Thermophoresis Effect on Microparticles in Micro Channel, Advances in Mechanical and Energy Technology, Springer, Lecture Notes in Mechanical
Engineering, pp. 285-296, ISBN 978-981-19-1617- 5. DOI: https://doi.org/10.1007/978-981-19-1618- 2_31, June 2022, Springer
Dewangan, A., B. Singh, A. Srivastava, A. Srivastava, A. K. Yadav, A Broad Review of Biodiesel Feedstocks with Competency to Replace Diesel, Advances in Mechanical and Energy Technology, Springer, Lecture Notes in Mechanical
Engineering, pp. 323-331, ISBN 978-981-19-1617- 5. DOI:, https://doi.org/10.1007/978-981-19-1618- 2_28, June 2022, Springer
A. Ahmad, A. Singh, D. K. Singh & A. K. Yadav, An Experimental Investigation of the Effect of Diethyl Ether as an Additive on the Performance of a Single Cylinder Diesel Engine, Recent Trends in Thermal and Fluid Sciences, Lecture Notes in Mechanical Engineering, pp. 69–75, ISBN: 978-981-19-3498-8, DOI: 10.1007/978-981-19-3498-8_7, Nov.2022. Springer
DOI: https://doi.org/10.37591/joaea.v9i3.6885
Refbacks
- There are currently no refbacks.