Open Access Open Access  Restricted Access Subscription or Fee Access

Wet Multi Plate Clutch Failure: A Review

Mukesh Kumar Mishra, Ashish Shrivastava, Abhishek Choubey


To create a successful design that satisfies modern demands, the traditional theoretical method of computing temperature area, in particular the maximum temperature considered inside the surfaces of the friction take hold of disc best during the single engagement, is used. The entire engagement time was 5s, although the temperature fields were calculated during 6 consecutive engagements. In order to calculate the heat conductivity of the friction grasp machine, a three-dimensional model of the friction surface of the grasp disc was created. During all encounters, the touch pressure between the contact surfaces became supposedly uniform. It was discovered that there had been numerous encounters


Dry friction clutch Successive engagements, Temperature distribution Finite element analysis

Full Text:



El-Sherbiny, M.; Newcomb, T.P. Temperature conveyances in car dry grasps. Proc. Inst. Mech. Eng., 190, 359–365, 1976

Maucher, P. Grip prattle. In Proceedings of the fourth International Symposium on Torsional Vibrations in the Drive Train, Baden-Baden, Germany, 20 April 1990.

A.E. Anderson: "Hot Spotting in Automotive contact Systems", J. of Wear, Vol. 135, No. 2, pp. 319‐337, 1990

Sawanobori, T.; Suehiro, T. An Analysis of Clutch Judder; SAE Technical Paper, No. 95131; SAE:Warrendale, PA, USA, 1995.

Bostwick, C.C.; Corp, C.; Corp, E. Self-energized vibrations during commitment of dry contact grasps. SAE Trans., 107, 689–701, 1998

Velardocchia, M.; Amisano, F.; Flora, R. A Linear Thermal Model for an Automotive Clutch; SAE Technical Paper, No. 2000-01-0834; SAE:Warrendale, PA, USA, 2000.

Crowther, A.R.; Zhang, N. Torsional limited components and nonlinearnumerical displaying in vehicle power train elements. J. Sound Vib., 284, 825– 849, 2005

Abdullah M. Al‐Shabibi and James R. Hair stylist: Transient Solution of The Unperturbed Thermo versatile Contact Problem, J. warm anxieties, Vol. 32, pp. 226‐243, 2009

M.M. Shahzamanian, B.B. Sahari, M. Bayat, Z.N. Ismarrubie and F. Mustapha: Transient and warm contact investigation for the versatile conduct of practically reviewed brake plates because of mechanical warm loads, J. Materials and Design, Vol. 31, Issue 10, pp. 4655–4665, 2010.

Menday, M.; Rahnejat, H. Rubbing arranging qualities and the grasp take judder wonder with manual transmission. In Tribology and Dynamics of Engine and Power train: Fundamentals, Applications and Future Trends; Rahnejat,H., Ed.;Woodhead Publishing: Cambridge, UK,; pp. 680–702, 2010

Abdullah M. Al-Shabibi, "The Thermo-mechanical Behavior in Automotive Brake and Clutch Systems," in New Trends and Developments in Automotive System Engineering,2010

Hua Fu, Li Fu, Ai-ping Liu, Guan-Lei Zhang "Constrained Element Analysis of temperature field of handle in Tunnel Boring Machine" WASE International Conference on Information Engineering, IEEE, 2010

Muhammad Mumtaz Jamil Akhtar, Oday I. Abdullah, Josef schlattmann "Transient Thermoelastic Analysis Of Dry Clutch System", Department of System Technology and Mechanical Design Methodology, 2013

Mamta G. Pawar, Monarch K. Warambhe, Gautam and R. Jodh "Plan and Analysis of Clutch Using Sintered Iron as a Friction Material", International Journal of Innovative Technology and Exploring Engineering., 2013

Dr. J. P. Modak, Shrikant V.Bhoyar, Dr. G. D. Mehta, ―Dynamic Analysis Of Single Plate Friction Clutch‖, IJERT, Vol. 2, Issue 7, July – 2013

Mr. P.Naga Karna, Tippa Bhimasankara Rao, ―Analysis of Friction Clutch plate using FEA‖ ,IJERD, Volume 6, Issue 2, March 2013

Prof.P.Baskar, Anil Jadhav, Gauri Salvi, Santosh Ukamnal, ―Static Structural Analysis of Multi plate Clutch with Different Friction Materials‖ IJERT, Volume 2, Issue 11, November 2013

Mr.Ganesh Raut, Anil Manjare, P Bhaskar ―Analysis of Multidisc Clutch Using FEA‖ IJETT, Volume 6, Dec 2013

Mr.N.V.Narasimharao.L, Ch.Chandrarao ―Static and Dynamic Analysis of Clutch Plate With Crack‖, IJRMET, Volume 4, Issue Spl - 1, Nov 2013

Mr. B. Nivas, M. Nithiyanandam, S. Tharaknath, A. AvinashKumar, ―Design and Analysis of Clutch Plate Using Steel Material [En – Gjs-400 - 15steel]‖, IOSR-JDMS, Volume 13, Issue 5, May. 2014

Mr.Rajesh Purohit, Pooja Khitoliya and Dinesh Kumar Koli, ―Design and Finite Element Analysis of an Automotive Clutch Assembly‖, ScienceDirect, Procedia Materials Science 6, 2014

Bony Chrisol Joseph , M Vasundara Structural Analysis of Multiplate Clutch using ANSYS ' worldwide journal of programming and hardware building vol 2 issue 05, 2014

Oday I. Abdullah, Wassan Abd AL-SAHB and Abdullah M. Al-Shabibi ,"Thermoelastic examination of multidisc Clutches using constrained segment procedure", 2014

Mr.Prashil M. Mhaiskar, Nitin D. Bhusale, Mayur D. Pastapure ―Vibration Analysis of Dry Friction Clutch Disk by Using Finite Element Method‖, IJERT, Volume 3, Issue 1, January – 2014

Rajesh Purohita, Pooja Khitoliyab and Dinesh Kumar Kolic "Plan and Finite Element Analysis of an Automotive Clutch Assembly "Procedia Materials Science 6 science direct ( 2014 ) 490 – 502

K.S.Aravindh, P Uma Mahesh, K Mohan Krishna3, J "FEM ANALYSIS OF WET MULTI PLATE CLUTCH BY VARYING FRICTION SURFACEMATERIAL" SaiSandeep4International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 02 Issue: 06 | Sep-2015

Guruprasad Shriwas Prakash Kumar Sen Gopal Sahu A Review on Wear Analysis and Heat Generation in Dry Friction Clutch IJSTE - International Journal of Science Technology and Engineering | Volume 2 , Issue 3 ,2349- 784, September 2015

Humphrey, E.; Gkinis, T.; Morris, N.J.; Leighton, M.; Rahmani, R.; RahnejatH. Griplining frictional qualities under warm tribodynamic conditions. In Proceedings of the third Biennial InternationalConference on Powertrain Modeling and Control , Loughborough, UK, 7–9 September 2016

Joel Martinsson , Bin Liu "Controlled Start Transmission Hydraulic Clutch Disk Temperature Modeling and Applications" Proceedings of IEEE International Conference on Mechatronics and Automation August 7 - 10, Harbin, China, 2016

Dr.Ch.S.Naga Prasad "Structure and Fatigue Analysis of a Multi Plate Clutch International Journal for Modern Trends in Science and Technology" Volume: 03, Issue No: 04, April 2017

Guguloth Ravi , Thurai Sharat and Maloth Heeralal "Structure EVALUATION OF A MULTI PLATE CLUTCH" March 2017 | IJIRT | Volume 3 Issue 10 | ISSN: 2349-6002

Vehicles Seyoum Kebede1, Hailemariam Nigus Hailu2 "Showing, and FEA of Multi-Plate Clutches by Varying Materials for Optimum Torque Transfer Capacity of TCT System of Green, And Light" International Journal of Advanced Engineering Research and Science (IJAERS) [Vol-5, Issue-1, Jan- 2018

M.H. Faidh-Allah a "The Temperature Distribution in Friction Clutch Disk under Successive Engagements" Tribology in Industry, Vol. 40, No. 1 (2018) 92-99,

Liping Li a, b, Zhaijun Lu a, *, Xue-Lai Liu b, Tao Sun b, Xingjian Jing c, Wen-Bin Shangguan b, " Modeling and assessment of contact handle at a driveline for smothering vehicle starting judder" Journal of Sound and Vibration science direct 424 (2018) 335e351

Gkinis, T.; Rahmani, R.; Rahnejat, H.; O'Mahony, M. Warmth age and move in car dry grasp commitment. J. Zhejiang Univ. Sci. A 19, 175–188, 2018

ZHENGFENG YAN, FUWU YAN, JIEJUNYI LIANG ,AND YALIN DUAN" Detailed Modeling and Experimental Assessments of Automotive Dry Clutch Engagement" Received April 8, 2019



  • There are currently no refbacks.