Open Access
Subscription or Fee Access
Comparison of microstructure and wear property of Al-30Pb alloy composite fabricated by spray forming and casting processes
Abstract
The influence of spray forming of Al-Pb alloy on its micro structure and wear behavior have been investigated. Aluminium alloys with lead 30%wt prepared via two methods viz. Casting and Spray casting process. The Al-Pb alloys are potential substances for bearing mixtures owing to the fact they possess most excellent performance like low price of production, friction properties, excessive non-corrosive effect, and excessive conductivity than different aluminum bearing alloys. Microstructural studies reveal dendritic morphology for casted Al -30Pb alloy and spray deposited Al-30 Pb alloy exhibits an even spreading of satisfactory globular formed phase. The received results of wear assessments of casted Al-30Pb alloy and spray formed Al-30Pb alloy were in contrast and the results shows that spray formed Al- 30Pb alloy possesses more wear resistance as compared to casted Al-30Pb alloy.
Keywords
References
Rashmi Mittal, Aruna Tomar, and Devendra Singh “Wear Behavior of Disk Shape Spray Formed Al- Si-Pb Alloys” Journal of Materials Engineering and Performance, JMEPEG (2014) 23:975–981, DOI: 10.1007/s11665-013-0802-x.
Rashmi Mittal, Aruna Tomar, Devendra Singh “Thickness uniformity and microstructure of disc shape spray formed Al-Si-Pb alloys” Adv. Mat. Lett. 2012, 3(1), 55-63, DOI: 10.5185/amlett.2011.5261.
Yu Fuxia, Cui Jianzhong , S. Ranganathan , E.S. Dwarakadasa “Fundamental differences between spray forming and other semisolid processes” Materials Science and Engineering A304–306 (2001) 621–626.
P. S. Grant “Spray forming” Progress in material science Vol. 39. pp 397v545. 1995, Copyright 1995 Elsevier Science Ltd.
Aruna Tomar, Rashmi Mittal, and Devendra Singh “Strength and elongation of spray formed Al– Si– Pb alloys” International Journal of Minerals, Metallurgy and Materials, Volume 21, Number 12, December 2014, Page 1222 DOI: 10.1007/s12613-014-1030-6.
Guang Ran, Jing-En Zhou, Shengqi Xi, Pengliang Li “Microstructure and morphology of Al–Pb bearing alloy synthesized by mechanical alloying and hot extrusion” Journal of Alloys and Compounds 419 (2006) 66–70, doi:10.1016/j.jallcom.2005.09.057.
Fuxiao Yua,, D.S. Dwarakadasab, S. Ranganathan “Microstructure and mechanical properties of spray-formed Al–Si–Pb alloys” Journal of Materials Processing Technology 137 (2003) 164–167, PII: S0924-0136(0 2 )010853
Gouthama, G.B. Rudrakshi, S.N. Ojha “Spray forming and wear characteristics of liquid immiscible alloys” Journal of Materials Processing Technology 189(2007) 224–230, doi:10.1016/j.jmatprotec.2007.01.026.
K. Raju, S. N. Ojha ,A. P. Harsha “Spray forming of aluminum alloys and its composites: an overview” J. Mater Sci (2008) 43:2509–2521,DOI 10.1007/s10853-008-2464-x.
J. An, Y.B. Liu, Y. Lu “The influence of Pb on the friction and wear behavior of Al–Si–Pb alloys” Materials Science and Engineering A 373 (2004) 294–302, doi:10.1016/j.msea.2004.01.051.
M. Zhu, Y. Gao, C.Y. Chung, Z.X. Che, K.C. Luo, B.L. Li “Improvement of the wear behaviour of Al–Pb alloys by mechanical alloying”, Wear 242 (2000). 47–53.
J. An, X.X. Shen, Y. Lu, Y.B. Liu “Microstructure and tribological properties of Al–Pb alloy modified by high current pulsed electron beam” Wear 261 (2006) 208–215, doi:10.1016/j.wear.2005.09.014.
Mustafa Kamal, Abu-Bakr El-Bediwi, and Samira El-Mohamady Fouda “Structural and Mechanical Characteristics of Al -Pb Alloys produced by chill-Block melt spinning” 131206-8989-IJET-IJENS
© December 2013 IJENS.
M. Zhu, Y. Gao , C.Y. Chung , Z.X. Che , K.C. Luo , B.L. Li “Improvement of the wear behaviour of Al–Pb alloys by mechanical alloying” Wear 242 _2000. 47–53.
Gururaj Hatti, Amith.V, Susilendra Mutalikdesai “Wear Behavior and Characterization of Spray Formed Al-Si and Al-Si-Sn Alloys” IJIRST Vol. 5, Issue 10, October 2016, DOI:10.15680/IJIRSET.2016.0510004.
Refbacks
- There are currently no refbacks.