The advanced bioceramics production using process of vibroturbulization

Authors

  • Michael Shoikhedbrod Electromagnetic Impulse Inc., 21 Four Winds Drive, Unit 12, North York, Ontario M3J 1K7, Canada

Keywords:

Advanced bioceramics processing, advanced bioceramics, Mixing, Vibroturbulization

Abstract

Currently, bioceramics are widely used in medicine as dental and bone implants. Surgical bioceramics are used regularly. Joint replacements are usually coated with bioceramics materials to reduce wear and tear and inflammation. Pacemakers, kidney dialysis equipment, and respirators are more instances of bioceramics being used in the medical field. The production process of bioceramics consists of the following four main steps: preparation of powder with a grain size of not more than 100 nm, mixing, shaping, compaction and finishing. The existing known methods of mixing do not allow obtaining promising bioceramics of uniform raw (unfired) density, since paddle mills are mainly used for mixing ceramic materials. Raw material powder particles and various impurities or sintering additives added to bioceramics powders, the distribution in the bioceramics material (usually one clay or one or more clays) during processing is critical for advanced bioceramics, and advanced bioceramics products must be uniform, completely dense, with high physical and chemical properties. This article presents a completely new mixing method in the main production process of advanced bioceramics. In the developed method, the mixing of particles, powder grains and various alloying or sintering additives injected into ceramic powders leads to their uniform distribution in the ceramic material, forming an unfired mixture of uniform density, due to vibration in the vibroturbulization process mode

Author Biography

  • Michael Shoikhedbrod, Electromagnetic Impulse Inc., 21 Four Winds Drive, Unit 12, North York, Ontario M3J 1K7, Canada
    Active Director

References

Muster D. Recovery and replacement of hard tissues with biomaterials 1992; ISBN 0- 444-88350-9.

Kinnari T. Esteban J. "Bacterial adherence to SiO2 based multifunctional bioceramics", Journal of Biomedical Materials Research, Part A, 2008); 89(1): 215–23pp. Doi: 10.1002 / jbm.a.31943.PMID 18431760.

Cassinger, Ruth. Ceramics: from magic pots to artificial bones. Brookfield, CT: Twenty-First Century Books 2003;ISBN 978-0761325857.

Market Overview: Marine Medical Ceramics Market, Acmite Market Intelligence2011.

Ceramics. Advanced Materials by Design, Chapter 2.1988; NTIS order #PB88-243548.

Processing and Properties of Advanced Ceramics and Glass, Workshop Proceeding, Vratna- Bela.

Greil P. Advanced engineering ceramics, Advanced Engineering Materials 4 (5). 2002; 247-254pp.

Shoikhedbrod M.P. Behavior of water under the influence of vibration and electric field, Lambert

Academic Publishing, Toronto. 2017.

Wegst UGK Bai H Saiz E Tomsia AP. Ritchie RO. Bioinspired structural materials. Nat Mater 2015;14:23-36.

Pasteris JD, Wopenka B, Valsami-Jones E. Bone and tooth mineralization: why apatite? Elements2008;4:97-104.

Takayanagi H. Osteoimmunology: shared mechanisms and crosstalk between the immune and bone systems. Nat Rev Immunol 2007;7:292-304.

Oryan A, Alidadi S, Moshiri A, Maffulli N. Bone regenerative medicine: classic options, novel strategies, and future directions. J Orthop Surg Res 2014;9:1

Downloads

Published

2022-09-08

Issue

Vol. 12 No. 2 (2022)

Section

Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.