Open Access
Subscription or Fee Access
Evaluation of process paramters of various materials by turning operation using different methodology techniques-A review
Abstract
The use of engineering materials has increased to a great extent in industries. So it is required to find the optimum parameters in order to have easy and economical machining. Turning operation is most important in the machining process. Especially of hard materials it is difficult sometimes to do so. For better results, the selection of proper process parameters is very important. This paper presents, the effect of process parameters on various materials while performing turning operation and been validated by various methodology techniques. It also highlights on the effect of input controllable parameters over the required output values. Taguchi was used to design experiment and to study its significance of cutting parameters ANOVA is carried out. Taguchi gives systematic simple approach and efficient method for the optimum operating conditions.
Keywords
References
Zou B, Zhou H, Huang C, Xu K, Wang J. Tool damage and machined-surface quality using hot-pressed sintering Ti (C 7 N 3)/WC/TaC Cermet cutting inserts for high-speed turning stainless steels. The International Journal of Advanced Manufacturing Technology. 2015 Jul 1;79(1–4):197–210.
Xu K, Zou B, Huang C, Yao Y, Zhou H, Liu Z. Machinability of Hastelloy C-276 using Hot-pressed sintered Ti (C 7 N 3)-based Cermet cutting tools. Chinese Journal of Mechanical Engineering. 2015 May 1;28(3):599–606.
Das A, Patel SK, Hotta TK, Biswal BB. Statistical analysis of different machining characteristics of EN-24 alloy steel during dry hard turning with multilayer coated Cermet inserts. Measurement. 2019 Feb 1;134:123–41.
Das A, Tirkey N, Patel SK, Das SR, Biswal BB. A comparison of machinability in hard turning of EN-24 alloy steel under mist cooled and dry cutting environments with a coated Cermet tool. Journal of Failure Analysis and Prevention. 2019 Feb 15;19(1):115–30.
Kumar R, Bilga PS, Singh S. Optimization and Modeling of Active Power Consumption for Turning Operations. InISME 19th Conference on advances in mechanical engineering (mechanical systems and sustainability) 2018; Vol. 19, pp. 1–16.
Pawar, P., Dabade, U. (2017). Analysis of Surface Roughness during Turning of AISI D2 steel. Journal of Advances in Science and Technology, 13, 219–226.
Umetne EZ, Ali ZU, Prevleko K. Experimental design and artificial neural network model for turning the 50crv4 (sae 6150) alloy using coated carbide/cermet cutting tools. Materiali in Tehnologije. 2014;48(2):227–36.
Murthy TS, Suresh RK, Krishnaiah G, Reddy VD. Optimization of process parameters in dry turning operation of EN 41B alloy steels with Cermet tool based on the Taguchi method. Optimization. 2013 Mar;3(2):1144–8.
Aruna M, Dhanalaksmi V. Design optimization of cutting parameters when turning Inconel 718 with Cermet inserts. International Journal of Mechanical and Aerospace Engineering. 2012 Jan 22;6:187–90.
Das A, Mukhopadhyay A, Patel SK, Biswal BB. Comparative assessment on machinability aspects of AISI 4340 alloy steel using uncoated carbide and coated Cermet inserts during hard turning. Arabian Journal for Science and Engineering. 2016 Nov 1;41(11):4531–52.
Das A, Patel SK, Biswal BB, Das SR. Machinability investigation and cost estimation during finish dry hard turning of AISI 4340 steel with untreated and cryo treated Cermet inserts. Journal of Superhard Materials. 2019 Jul 1;41(4):247–64.
Mohammadi A, Zarepour H. Statistical Analysis of Hard turning Of AISI 4340 Steel on surface finish and Cutting Region Temperature. Advanced Materials Research 2010; Vol. 83, pp. 303–314. Trans Tech Publications Ltd.
Suresh R, Basavarajappa S, Gaitonde VN, Samuel GL. Machinability investigations on hardened AISI 4340 steel using coated carbide insert. International Journal of Refractory Metals and Hard Materials. 2012 Jul 1;33:75–86.
Kumar R, Sahoo AK, Das RK, Panda A, Mishra PC. Modelling of flank wear, surface roughness and cutting temperature in sustainable hard turning of AISI D2 steel. Procedia Manufacturing. 2018 Jan 1;20:406–13.
Aslan E. Experimental investigation of cutting tool performance in high speed cutting of hardened X210 Cr12 cold-work tool steel (62 HRC). Materials & design. 2005 Feb 1;26(1):21–7.
Garg M, Kainth M, Grover G. Determination of Optimum Process Parameters during turning on CNC Lathe of EN8 & EN24 Steels using Taguchi method and ANOVA.
Aouici H, Bouchelaghem H, Yallese MA, Elbah M, Fnides B. Machinability investigation in hard turning of AISI D3 cold work steel with ceramic tool using response surface methodology. The International Journal of Advanced Manufacturing Technology. 2014 Aug;73(9):1775–88.
Ranganath MS, Vipin H. Surface Roughness Prediction Model for CNC Turning of EN-8 Steel Using Response Surface Methodology. International Journal of Emerging Technology and Advanced Engineering. 2015;5(6): 135–43.
Adinarayana M, Prasanthi G, Krishnaiah G. Parametric analysis and multi objective optimization of cutting parameters in turning operation of AISI 4340 alloy steel with CVD cutting tool. International Jour
nal of Research in Engineering and Technology. 2014;3(02):449–56.
Suresh RK, Venkataramaiah P, Krishnaiah G. Experimental investigation for finding optimum surface roughness, VMRR and interface temperature during turning of AISI 8620 alloy steel using CNMG insert. International Journal of current Engineering and Technology. 2014;4(4).
Parmar KV, Thakkar HR. A Technical Review on Ceramic Cutting Tool Inserts. Trends in Mechanical Engineering & Technology. 2018 Nov 23;8(3):7–11.
DOI: https://doi.org/10.37591/tmet.v10i3.4201
Refbacks
- There are currently no refbacks.